06-27-2007
Seems your adapter firmware might be the problem:
http://www14.software.ibm.com/webapp...=FC6239FW.html
Your level doesn't get a mention so it was either never released (although some cards may have been shipped with it) or it was withdrawn for some reason.
As you are at a recent level of AIX 5.2 I'd check all system / adapter firmware is up to date 'cos IBM won't have tested late levels of AIX on old or "unknown" firmware levels.
10 More Discussions You Might Find Interesting
1. BSD
is me again guys, sorry for the mistake in the written, what the problem is, i can't connect to the internet because i did a bad configuration in the freebsd os, i use a yahoo dsl modem and i don't dial to my isp, but everytime i try to connect ask me for a phone number to connect to my isp, what... (1 Reply)
Discussion started by: nobody
1 Replies
2. Solaris
I Have IBM ESS 800, trying to configure SAN storage using Fiber card. I installed the SDD driver & can see the disks however, when I did
# datapath query device
I have the disks shown in slices
# ./datapath query device
Total Devices : 8
Dev#: 0 Device Name: vpath1a Type:... (0 Replies)
Discussion started by: Remi
0 Replies
3. AIX
Hi all,
Sorry if this is in the wrong place but needed to make sure lots of people saw this so that hopefully someone will be able to help.
Basically i've upgraded a test server from 4.3 to 5.3 TL04.
The server has hdisk0 and 1 as rootvg locally but then has another vg setup on our ESS... (5 Replies)
Discussion started by: djdavies
5 Replies
4. AIX
Sorry for my english.
We have a IBM BLADES JS21. AIX 5.3 update to 6.
Our JS21 has 2 FC (fcs0 and fcs1).
We have one DS4072, one Disk system with 2 controllers and 2 FC by controllers.
This means, all AIX FC see all Disk systems controllers by 2 FC switchs. (one fc two roads)
FC AIX... (4 Replies)
Discussion started by: fjgonzalez
4 Replies
5. UNIX for Advanced & Expert Users
Hi,
I have 4 servers that I connected SUN HBAs on. (SAN is IBM - ESS 800 with Brocade switch)
I installed the SAN foundation kit, IBMsdd drivers, Solaris Patch 108974-50 & SANsurfer CLI.
(I'm running Solaris 8 - HBA is SG-XPC11FC-QL2
On 1 of the 4 servers show the HBAs as CONNECTED, but... (3 Replies)
Discussion started by: Remi
3 Replies
6. AIX
Hi All,
I have mirrored SAN volume on my B80 rootvg. Can I just remove the mirror and "Remove a P V from a V G" and it will be a diskless AIX?
Is that going to boot on SAN rootvg volume?
Thanks in advance,
itik (3 Replies)
Discussion started by: itik
3 Replies
7. AIX
Hi All,
I need to do maintenance on the SAN. Do I need to shutdown AIX as well? Or I can just unmount the SAN-FS and let the SAN reboot or do maintenance mode. And then when SAN is up, just mount it back.
Is that simple it is or not?
Thanks in advance,
itik (1 Reply)
Discussion started by: itik
1 Replies
8. AIX
Hi All,
How do I pull out the wwpn of san interface on aix53?
Any idea, thanks. (1 Reply)
Discussion started by: itik
1 Replies
9. Solaris
HI All,
What are IPFC(Internet Protocol over Fibre channel) SAN devices.
What all i got from guide is
"Configuring IPFC over host system describes host recognition of IPFC devices and implementation of IP over FC in SAN"
What does above statement actually mean. I would appreciate detailed... (2 Replies)
Discussion started by: ravijanjanam12
2 Replies
10. Emergency UNIX and Linux Support
Setup:
Multiple Virtual Machines running OEL5 / Oracle RDBMS 11.2
OVM 2 / Xen 3.4.0 Cluster consisting of 3 Machines
Shared SAN Storage synced with OCFS2
SAN connected with 4GB FC on 4 Paths per LUN
SAN target are 2 EMC Clariion mirroring each other
The problems we're facing are that... (6 Replies)
Discussion started by: pludi
6 Replies
IPWFW(4) BSD Kernel Interfaces Manual IPWFW(4)
NAME
ipwfw -- Firmware Module for Intel PRO/Wireless 2100 driver
SYNOPSIS
To compile this module into the kernel, place the following line in your kernel configuration file:
device ipwfw
This will include three firmware images inside the kernel. If you want to pick only the firmware image for the mode you want to operate your
network adapter in choose one of the following:
device ipwbssfw
device ipwibssfw
device ipwmonitorfw
Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):
ipw_bss_load="YES"
ipw_ibss_load="YES"
ipw_monitor_load="YES"
DESCRIPTION
This module provides access to firmware sets for the Intel PRO/Wireless 2100 series of IEEE 802.11 adapters. It may be statically linked
into the kernel, or loaded as a module.
For the loaded firmware to be enabled for use the license at /usr/share/doc/legal/intel_ipw/LICENSE must be agreed to by adding the following
line to loader.conf(5):
legal.intel_ipw.license_ack=1
FILES
/usr/share/doc/legal/intel_ipw/LICENSE ipwfw firmware license
SEE ALSO
ipw(4), firmware(9)
BSD
January 14, 2010 BSD