Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is... (3 Replies)
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OPENSOLARIS
net_phylookup
net_phylookup(9F) Kernel Functions for Drivers net_phylookup(9F)NAME
net_phylookup - determine if a network interface name exists for a network protocol
SYNOPSIS
#include <sys/neti.h>
phy_if_t net_phylookup(const net_data_t net, const char *name);
INTERFACE LEVEL
Solaris DDI specific (Solaris DDI).
PARAMETERS
net value returned from a successful call to net_protocol_lookup(9F).
name name of the network interface to find.
DESCRIPTION
The net_phylookup() function attempts to resolve the interface name passed in with the network protocol.
When called successfully, the value returned represents a network interface that exists, at the time of the call, within the scope of the
network interface. This value is only guaranteed to be unique for a name within the scope of the network protocol.
RETURN VALUES
The net_phylookup() function returns -1 if it is not supported by the network protocol, and 0 if the named network interface does not
exist (or is otherwise unknown). Otherwise, it returns a value greater than 0 representing a network interface that currently exists
within the scope of this network protocol.
CONTEXT
The net_phylookup() function may be called from user, kernel, or interrupt context.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Committed |
+-----------------------------+-----------------------------+
SEE ALSO net_getifname(9F), net_phygetnext(9F), net_protocol_lookup(9F), attributes(5)SunOS 5.11 1 May 2008 net_phylookup(9F)