06-19-2007
Problem is, i need to create a script which will run against 3000 servers and check to see if any of them has Broadcome card as eth0 or eth4. Broadcome can be eth1,2,3,5,6 but not eth0 or eth4.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Dummies Questions & Answers
I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is... (3 Replies)
Discussion started by: 98_1LE
3 Replies
3. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
4. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT OPENDARWIN
tc-matchall
Match-all classifier in tc(8) Linux Match-all classifier in tc(8)
NAME
matchall - traffic control filter that matches every packet
SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ]
DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
skip_sw
Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter-
face, operation will fail.
skip_hw
Do not process filter by hardware.
EXAMPLES
To create ingress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that
mirrors the packets to device eth2.
To create egress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle 1: root prio
tc filter add dev eth1 parent 1:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a
matchall filters on it that mirrors the packets to device eth2.
To sample one of every 100 packets flowing into interface eth0 to psample group 12:
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: matchall
action sample rate 100 group 12
SEE ALSO
tc(8),
iproute2 21 Oct 2015 Match-all classifier in tc(8)