Get info on network interface Post: 302122237

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. UNIX for Dummies Questions & Answers

I can't remember or figure out how to do this. What is the command(s) in Solaris 8 sparc to show the values operating a NIC, specifically the negotiated transfer rate (10/100) and mode (full/half duplex)? Also, how can I force 100 Mb full (the network is just a crossover cable, and the other box is...

3. UNIX for Advanced & Expert Users

network interface problem

Hi expert, Need some help on network interface issue.. I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0...

4. IP Networking

How to activate a network interface?

What are the steps between "ifconfig eth0 UP" and "net_device->open"? ifconfig eth0 UP => ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) => ????? => what are these steps? net_device->open Thanks!

5. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

6. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

7. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

8. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

9. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT DEBIAN

aoe-interfaces

aoe-interfaces(8)					      System Manager's Manual						 aoe-interfaces(8)

NAME

       aoe-interfaces - restrict aoe driver to specified network interfaces

SYNOPSIS

       aoe-interfaces [dev1] [dev2 ...]
       aoe-interfaces -c

DESCRIPTION

       The  aoe-interfaces command tells the aoe driver to ignore ATA over Ethernet (AoE) traffic on all but the specified network interfaces.	It
       is analogous to the aoe_iflist module load option.

       If neither the aoe_iflist module load option nor the aoe-interfaces command are used, the aoe driver will use any network interface for AoE
       traffic.   Using  aoe-interfaces  to limit AoE to only trusted networks prevents the case where a rogue AoE target appears on a public net-
       work, diverting data from the legitimate AoE target.  Such an imposter target effectively corrupts the data on the legitimate target.

       If the aoe driver is a module, then calling aoe-interfaces without arguments will display the current interfaces list.  If it  hasn't  been
       set then the output will be blank.

       It's good to run the aoe-discover command after setting the AoE interfaces list.

OPTIONS

       -c     The -c flag will clear the interface access list, permitting any interface to be used.

EXAMPLE

       In  this  example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic.  After remembering that
       shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then  calls  aoe-discover
       to ask the aoe driver to look for new AoE devices.

	      nai:~# modprobe aoe aoe_iflist="eth0"
	      nai:~# aoe-stat
		 e10.9		  eth0		    up
	      nai:~# aoe-interfaces eth0 eth3
	      nai:~# aoe-discover
	      nai:~# aoe-stat
		  e7.0		  eth3		    up
		  e7.1		  eth3		    up
		  e7.2		  eth3		    up
		  e7.3		  eth3		    up
		  e7.4		  eth3		    up
		  e7.5		  eth3		    up
		  e7.6		  eth3		    up
		  e7.7		  eth3		    up
		  e7.8		  eth3		    up
		  e7.9		  eth3		    up
		 e10.9		  eth0		    up
	      nai:~# aoe-interfaces
	      eth0 eth3

SEE ALSO

       aoe-discover(8), aoe-stat(8), aoetools(8).

AUTHOR

       Ed L. Cashin (ecashin@coraid.com)

																 aoe-interfaces(8)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. UNIX for Dummies Questions & Answers

network interface questions

Discussion started by: 98_1LE