Compaq Proliant ML370 G2 with Broadcom BCM5703 NIC Post: 302121336

9 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

Create RAID - Smart Array Tool - ML370

Hi guys, i must install an old old old ml370 server... I must create a RAID 5 with my 4 SCSI disk. I need a SmartStart disk for create it or a Floppy Disk called "Array configuration Tool". I don't find it on the hp website...:mad::mad::mad: Anyone have it?? Thanks in advance. Zio

2. Solaris

Solaris 10 and Broadcom drivers

Hi to all, I've installed Solaris 10 on my workstation but I've some networks problems.My NIC,a Broadcom integrated chipset don't work with solaris.Whit the prtconf command I'm unable to identify the correct chipset's model.And I'm searching hovewer for some drivers but I'm fear that Broadcom...

3. BSD

Broadcom 4312 in BSD

Is there a way to configure Broadocom wifi 4312 in a bsd system, FreeBSD or OpenBSD. I will appreciate any kind of help. Thanks in advance

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux...

5. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance!

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome....

7. Solaris

Broadcom driver for Solaris

I'm having the hardest time finding the Broadcom drivers for Solaris. I need an odd ball, 32-bit for Solaris 10. Anyone know where I can find one?

8. Linux

Broadcom under Fedora 18 (Spherical Cow)

So I'm having a problem getting a Broadcom BCM4312 wireless controller to work under the broadcom-wl module $uname Linux 3.8.11-200.fc18.x86_64 #1 SMP Wed May 1 19:44:27 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux lspci -v 05:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g...

9. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected...

LEARN ABOUT DEBIAN

adjtimexconfig

ADJTIMEXCONFIG(8)					      System Manager's Manual						 ADJTIMEXCONFIG(8)

NAME

       adjtimexconfig - find kernel clock variables and save for reboots

SYNOPSIS

       /sbin/adjtimexconfig

DESCRIPTION

       This script uses adjtimex(8) to find values for the kernel variables tick and frequency that will make the system clock approximately agree
       with the CMOS clock.  It then saves these values in the configuration file /etc/default/adjtimex so the settings will be restored on every
       boot, when /etc/init.d/adjtimex runs.

       adjtimexconfig uses the drift rate recorded in /etc/adjtime to adjust the times it reads from the CMOS clock.  If you find the CMOS clock
       has a systematic drift, read the clock(8) or hwclock(8) manual page, modify /etc/adjtime as required, and run adjtimexconfig again.

AUTHOR

       Michael Meskes <meskes@debian.org>.

FILES

       /etc/default/adjtimex
       /etc/init.d/adjtimex

SEE ALSO

       adjtimex(8), clock(8), hwclock(8), ntpd(8)

								  April 27, 2003						 ADJTIMEXCONFIG(8)