06-07-2007
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
Hi,
How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies
2. IP Networking
I have searched this forum for solution and have drawn a blank... so I come to you for help :)
I an a Win XP user that has no problem getting on internet when I am on that OS (currently on it right now ;)). I installed red hat 9 and when I use that OS, I cannot get a connection. I ran the... (10 Replies)
Discussion started by: Minnesota Red
10 Replies
3. UNIX for Advanced & Expert Users
i purchased, what was labeled as a 4-port fast ethernet sbus card from ebay.
i installed it in my ultra1, and it seems to be working fine. how can i determine if the card is infact a fast ethernet card vs. the standard ethernet 4-port card? (7 Replies)
Discussion started by: xyyz
7 Replies
4. SCO
Installed a replacement 3com pci card on an ibm PC 300 GL, running OpenServer 6.0 , brought up system, and recieved this message:
Fsstat:/dev/boot mounted
Mounted /stand filesystem
System auditing is not enabled.
Dlpid:Unable to open network adapter driver (/dev/mdi/r8e0)
Dlpid:No such... (0 Replies)
Discussion started by: tazmss1
0 Replies
5. IP Networking
What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies
6. AIX
Hi,
is it possible to find out network utilization of etherenet card in %?
Regards,
Manoj (2 Replies)
Discussion started by: manoj.solaris
2 Replies
7. Red Hat
Hi guys,
Suppose you have a server with two ethernet cards (1GB each) and each cards are connecting to two different switches cisco 3750. My question is:
How can I setup my server's network interfaces to increase the throughput up to 2GB? is it possible? If not, do you know another way to up... (3 Replies)
Discussion started by: iga3725
3 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. Solaris
Hi Gurus of Solaris.
I have a problem yesterday when I was installing solaris in a x86 equipement
I attached some log that I capture when I try to resolve the problem
Any guru that can help please.
Any command or procedure that I can run, please advice me
Regards
Andres (10 Replies)
Discussion started by: andresguillen
10 Replies
10. AIX
Hello.
I have a server RS/6000 with AIX 4.2. The server have a network card with 10/100mbps speed, but for some reason, the ethernet only runs at 10Mbps, it doesn,t matter if I put the net cable on a 100Mbps switch, it keeps running at 10Mbps speed....
I know how to view/change ethernet speed... (1 Reply)
Discussion started by: little_ball
1 Replies
LEARN ABOUT REDHAT
tc574_cs
3C574_CS(4) Kernel Interfaces Manual 3C574_CS(4)
NAME
3c574_cs - 3Com 3c574 Etherlink XL 10/100 PC Card device driver
SYNOPSIS
insmod 3c574_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...] [full_duplex=n] [auto_polarity=n] [max_interrupt_work=n]
DESCRIPTION
3c574_cs is the low-level Card Services driver for the 3Com 3c574 EtherLink XL PCMCIA ethernet adapter. When this driver is attached to a
card, it allocates the next available ethernet device (eth0..eth#). This device name will be reported in the kernel log file, and passed
on to cardmgr(8).
The driver uses the N-Way autonegotiating transceiver to negotiate the speed and duplex of the network link. If the link partner does not
support negotiation, only the link speed is detected.
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
if_port=n
Selects the transceiver type. Only 0, 1, and 4 are acceptable values, other values return an error. This actual value specificed
is ignored -- the autonegotiating transceiver selects the media speed and duplex used.
irq_list=i,j,...
This option limits the set of interrupts that may be allocated by this driver. The default is all normally-usable IRQs.
full_duplex=n
This flag determines if only full-duplex modes are advertised. It defaults to 0 (false).
This flag can be used to control the transceiver's auto polarity
detection capability. Some Cisco Catalyst switches are known to interact badly with this feature in 10baseT mode. It defaults to 1
(enabled).
max_interrupt_work=work-limit
This option selects the maximum amount of work handled during each interrupt. Each received packet counts as one unit of work, as
does updating statistics counters and handling errors. The default is 32.
DIAGNOSTICS
eth#: interrupt(s) dropped!
Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi-
cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration
problem.
AUTHOR
Driver core: Donald Becker - becker@scyld.com
PC Card interface: David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5), ifport(8).
pcmcia-cs $Date 3C574_CS(4)