06-04-2007
Sounds like you're having a hardware issue, but still, we cannot determine the problem without knowing the OS version. As Blowtorch asked, post output of "uname -a" command. This looks like a specific OS system core dump and we cannot be sure, but as possible move, I'd suggest that you contact the vendor.
Some more :
Quote:
The parity error will typically occur as soon as the system completes the power-on self test; the memory count that is performed will typically pass without any problems being recognized. The most common cause of parity errors when first booting up the PC are incorrect configuration or using the wrong type of memory. It is unusual for an actual memory failure, of the type that parity checks for (meaning, you wrote one value into memory and read back another value with a bit changed) to be encountered at the start of booting, although it is possible.
9 More Discussions You Might Find Interesting
1. HP-UX
Hi,
where can i get Hp unix dummy version to use in my home system.iam a newbie to unix.pls let me know if any avilable..Thank you Shruti (6 Replies)
Discussion started by: shruti_mgp
6 Replies
2. AIX
HI Everybody,
I am a newbie of using AIX, would you mind telling me how to setup JOE and OpenSSH in AIX 5L 5.3. Thanks!
Hugo (0 Replies)
Discussion started by: tknl
0 Replies
3. UNIX for Dummies Questions & Answers
hi,
im new to unix.i dont have unix software in my system.
Is there any website is there to practice unix in online
can u please any one help me......
thanks in advance (3 Replies)
Discussion started by: gowridoc
3 Replies
4. AIX
HI Guys,
I have AIX 5.3 with TL05 ...I am trying to install HDLM 5.80/5.81 on this.
Installed Hitachi.aix.support.rte file set.
HDLM kept on installing ...it is not comming out .command status is "running"
============================================
Command: running stdout: yes ... (0 Replies)
Discussion started by: b_manu78
0 Replies
5. UNIX for Dummies Questions & Answers
Hi All,
From where can i get the UNIX Software so that i can install the same in my Laptop.
Thanks
Dilip (2 Replies)
Discussion started by: DilipPanda
2 Replies
6. Solaris
Estou tentando instalar o software de HDLM ( Hitachi Dynamic Link Manager ) e está apresentando a seguinte mensagem:
-bash-3.00# ./installhdlm
KAPL09187-W No parameter is specified.
Não sei que parameter é esse ? (1 Reply)
Discussion started by: to.brunoaugusto
1 Replies
7. Solaris
I'm trying to install the software HDLM (Hitachi Dynamic Link Manager) and is presenting the following message:
-Bash-3.00 #./Installhdlm
In KAPL09187-W parameter is specified.
I do not know which parameter is that? (3 Replies)
Discussion started by: to.brunoaugusto
3 Replies
8. AIX
Hi to all
please help ...Acutally i m new in AIX. I dont much know about AIX. I m totally confusing with software management chapter. Actually i m not getting difference between.
LPP,,BUNDLE,,,PACKAGE,,FIXES,,,APAR,,,,,FILESET.....
i read in the book.......as i know about RPM in linux.....but in... (2 Replies)
Discussion started by: life008
2 Replies
9. Solaris
hi all
i am working on zone and when i try to install software
i face read and write permisssion on directory which zonning inherit from them
so how can i add read and write permission to zone already running (3 Replies)
Discussion started by: jamisux
3 Replies
dpt(7D) Devices dpt(7D)
NAME
dpt - DPT ServeRAID IV SCSI host bus adapter and RAID adapter driver
DESCRIPTION
The dpt driver is a driver for the DPT (Distributed Processing Technology) family of SmartRAID IV SCSI HBA and RAID adapters. The following
HBA adapters are supported: PM2024, PM2044UW, PM2044W, PM2124, PM2124W, PM2144UW, and PM2144W.
The following RAID adapters are supported: PM3224, PM3224W, PM3334UW, and PM3334W.
PRECONFIGURATION
o DPT PM3224 only: Only EPROM 7A and later versions are supported.
o DPT PM2024 and PM2124 only: Only EPROM 6D4 and later versions are supported.
o Use adapters with SmartROM version 3.B or later versions only.
o Be sure that the controller board is installed in a PCI bus-mastering slot.
o Disable PCI parity checking if your firmware version is earlier than version 7A, if your system memory is ECC, or if your system does
not check parity.
Known Problems and Limitations
During system boot, a message may be displayed saying a DPT controller driver cannot be installed. This message indicates that the mother-
board installed in your system may contain ECC memory or may not check parity. If you see this message is displayed, disable PCI parity
checking.
Supported Settings
o I/O Address: Auto
CONFIGURATION
Auto-configuration code determines whether the adapter is present at the configured address and what types of devices are attached to it.
The DPT ServeRAID is primarily used as a disk array (system drive) controller.
To configure the attached disk arrays, you must configure the controller (using the configuration utilities provided by the hardware manu-
facturer) before you boot the Solaris operating environment. You use the configuration utilities to set RAID levels, stripe parameters,
cache mechanisms and perform other functions. For more information, see the user manual supplied with your hardware.
FILES
/kernel/drv/dpt.conf dpt configuration file
/dev/dsk/cndn[s|p]n block device
/dev/rdsk/cndn[s|p]n raw device where:
cn controller n
dn LUN n (0-7)
sn UNIX system slice n (0-15)
pn fdisk(1M) partition(0)
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
|Architecture |x86 |
+-----------------------------+-----------------------------+
SEE ALSO
fdisk(1M), attributes(5), cmdk(7D)
SunOS 5.10 27 November 2000 dpt(7D)