Sponsored Content
Full Discussion: SD/MMC card
Operating Systems Linux SD/MMC card Post 302117380 by nathan on Monday 14th of May 2007 01:01:36 AM
Old 05-14-2007
What happens when you plug in an SD/MMC card? A lot of times the device (card in this case) will be automounted. Type 'df' before inserting the card, then insert the card, wait a few seconds and type 'df' again. If the card was automounted, there will be a new line in the output that wasn't there before.

I believe those .h files are for compiling a linux kernel and/or any kernel modules/extensions. You shouldn't have to use those to get your SD/MMC port to work.
 

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

sound card ?????

sapp guys i've got this little problem, i have no idea what kind of sound card i got i check dmesg|more and its not there is there any other way to find out ? THX (4 Replies)
Discussion started by: challenger
4 Replies

2. UNIX for Dummies Questions & Answers

Please help me with my sound card...

Hello, I have recently installed Red Hat 7.3 next to my Windows XP. Everything works fine, except for the sound card (Sound Blaster Audigy), which is not supported yet. I heard that I can install SB Live! drivers to get it to work, but being a complete linux newbie I don't know how to do that. Can... (3 Replies)
Discussion started by: LittleMan
3 Replies

3. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a (1 Reply)
Discussion started by: dhlopomo
1 Replies

4. Linux

wireless card

Ive been fooling around on my spare laptop and put different cores of Fedora on and the computer uses an ibm a/b/g card but the os wont recognize the card and doesnt have the software fore it is there anyway to get the software for the card on the comp or should i buy a card that the os knows? (7 Replies)
Discussion started by: Texasone
7 Replies

5. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

6. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

7. UNIX Desktop Questions & Answers

Does Red Hat Fedora support Nvidia card 8800GTX and 260 card?

Does Red Hat Fedora support Nvidia card 8800GTX and 260 card? Does any Linux OS support Nvidia card? (1 Reply)
Discussion started by: sito
1 Replies

8. Filesystems, Disks and Memory

Raid Card

I have a compaq system that only supports IDE drivers, I use on it FreeBSD and debian. I want to get a Raid card that supports Raid 1. Which card Should i get that would be fully supported?? i dont want to spend more than $60 thanks :) (0 Replies)
Discussion started by: supermiguel
0 Replies
LAPTOP_MODE(8)						      System Manager's Manual						    LAPTOP_MODE(8)

NAME
/usr/sbin/laptop_mode - apply laptop mode settings SYNOPSIS
/usr/sbin/laptop_mode [ cmd ] [ force ] DESCRIPTION
This manual page documents briefly the /usr/sbin/laptop_mode command. laptop_mode is a program that applies the settings given in the /etc/laptop-mode/laptop-mode.conf configuration file. The primary use is to control the laptop mode feature included in Linux kernels with versions 2.6.6 and higher, and 2.4.23 and higher. This feature increases battery life by letting your hard drive spin down. This is achieved by grouping disk write activity into "chunks" that are spaced at larger intervals than they normally would be. In addition to sup- porting the Linux kernel's laptop mode feature, /usr/sbin/laptop_mode also supports various power saving modules which are configured through configuration files in the /etc/laptop-mode/conf.d directory. It is not recommended to call /usr/sbin/laptop_mode directly to start or stop laptop mode, except in hardware event handlers. To apply new configuration settings from laptop-mode.conf, call the laptop-mode service init script with the reload parameter. COMMANDS
Specify force as the second parameter to force laptop_mode to re-apply a state even if the computer is already in that state. These are the values that are allowed for cmd : auto Enable or disable laptop mode based on the current power state. Note that this will not do anything if the laptop-mode service has not been started! status Display a status report about everything that laptop_mode affects. SEE ALSO
laptop-mode.conf(8). AUTHOR
This manual page was written by Bart Samwel (bart@samwel.tk) for the Debian system (but may be used by others). Permission is granted to copy, distribute and/or modify this document under the terms of the GNU General Public License, Version 2 any later version published by the Free Software Foundation. On Debian systems, the complete text of the GNU General Public License can be found in /usr/share/common-licenses/GPL. LAPTOP_MODE(8)
All times are GMT -4. The time now is 04:18 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy