Network device driver Post: 302114677

4 More Discussions You Might Find Interesting

1. Solaris

SUNWglmr -- rasctrl environment monitoring driver for i2c or SCSI device driver ?

I've been researching minimizeing Solaris 8 and found that on the web page http://www.sun.com/bigadmin/content/packagelist/s8u7PkgList/p2.html the package SUNWglmr is listed as "rasctrl environment monitoring driver for i2c, (Root) (32-bit)" while in the document "Solaris 8 minimize-updt1.pdf"...

2. UNIX for Advanced & Expert Users

help regarding device driver

Hi All, I have a device driver that uses UARTserial port to write/read to-from a device. That device driver is working fine on FC3 machine( kernel version 2.6.12)... Now I am switching to FC9 (kernel version 2.6.25.11-97).I have changed the interrupt flag SA_INTERRUPT to IRQF_DISABLED...

3. Programming

regarding device driver

4. Red Hat

Unable To Activate Ethernet Network Device in RHEL 5.5 - e100 device eth0 does not seem to be presen

Hi All, Could anyone please help to resolve the below problem. I installed RHEL5.5 in my desktop.But when i try to activate the ethernet connection then it gives me the error. I spent 2 days for the above and go through with several suggestion found by googling. But no luck. ...

LEARN ABOUT FREEBSD

if_urtw

URTW(4) 						   BSD Kernel Interfaces Manual 						   URTW(4)

NAME

     urtw -- Realtek RTL8187B/L USB IEEE 802.11b/g wireless network device

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device ehci
	   device uhci
	   device ohci
	   device usb
	   device urtw
	   device wlan

     Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_urtw_load="YES"

DESCRIPTION

     The urtw driver supports USB 802.11b/g wireless adapters based on the Realtek RTL8187B/L.

     urtw supports station and monitor mode operation.	Only one virtual interface may be configured at any time.  For more information on config-
     uring this device, see ifconfig(8).

HARDWARE

     The urtw driver supports Realtek RTL8187B/L based wireless network devices, including:

	   Card 			 Radio	    Bus
	   Belkin F5D7050E		 RTL8225    USB
	   Linksys WUSB54GCv2		 RTL8225    USB
	   Netgear WG111v2		 RTL8225    USB
	   Netgear WG111v3		 RTL8225    USB
	   Safehome WLG-1500SMA5	 RTL8225    USB
	   Shuttle XPC Accessory PN20	 RTL8225    USB
	   Sitecom WL168v1		 RTL8225    USB
	   Sitecom WL168v4		 RTL8225    USB
	   SureCom EP-9001-g(2A)	 RTL8225    USB
	   TRENDnet TEW-424UB V3.xR	 RTL8225    USB

EXAMPLES

     Join an existing BSS network (i.e., connect to an access point):

	   ifconfig wlan create wlandev urtw0 inet 192.168.0.20 
	       netmask 0xffffff00

     Join a specific BSS network with network name ``my_net'':

	   ifconfig wlan create wlandev urtw0 ssid my_net up

     Join a specific BSS network with 64-bit WEP encryption:

	   ifconfig wlan create wlandev urtw0 ssid my_net 
		   wepmode on wepkey 0x1234567890 weptxkey 1 up

SEE ALSO

     intro(4), netintro(4), usb(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8)

     Realtek, http://www.realtek.com.tw.

HISTORY

     The urtw device driver first appeared in FreeBSD 8.0.

AUTHORS

     The urtw driver was written by Weongyo Jeong <weongyo@FreeBSD.org>.

BSD
								 October 17, 2009							       BSD