Sponsored Content
Operating Systems SCO xp/sco 5.0.7 dual boot issues Post 302114673 by jgt on Tuesday 17th of April 2007 07:43:58 PM
Old 04-17-2007
If you must

Add a second hard drive to the system, large enough to hold /u for unix and D: for XP.
Check the CMOS settings for the primary drive and determine how many megabytes are available before you reach cylinder 1023. Change the geometry to suit using LBA or LARGE in order to achieve the required amount.
You will probably need about 2gb for each OS.
This should not be a problem, I checked my own 20gb disk and it has 2400 cylinders, so that it would have about 8gb before cylinder 1023.
Install XP on a partition that is only 4gb.
Install SCO on whatever remains on the primary drive, only /stand needs end before cylinder 1023.
If there is not enough room left for the SCO apps and data then partition the second hd with fdisk to provide one unix partition and one NTFS partition
On the XP side use the second hard disk as drive D and then when you install any applications, install them on D not C.
Make the unix partition active.
Then you should be able to type XP at the 'boot:' prompt and have XP run.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

problem in dual boot

i want to know how do i make my system a dual boot system for Linux 7.1 and Windows Nt 4.0 :( :confused: :confused: (2 Replies)
Discussion started by: mad2life
2 Replies

2. UNIX for Dummies Questions & Answers

Dual boot no more

Ok I had a windows and RH dual boot system and have now converted over completly to the linux system. How do I regain the other half of my drive? I cannot see it in the disk manager. what do I do to format so that i can mount it? (1 Reply)
Discussion started by: macdonto
1 Replies

3. UNIX for Dummies Questions & Answers

Dual Boot help...

Hi there! I have a laptop which I plan on installing a dual boot on with Windows and Linux. I have Windows 98 installed at the moment, and I also have a copy of Slackware 8. I talked to friend, and he said he had some problems installing a dual boot with linux on his laptop... So I just came... (2 Replies)
Discussion started by: satan404
2 Replies

4. UNIX for Dummies Questions & Answers

Dual Boot Solaris 8

Greetings, I have learned much since joining the message board, but I was unable to locate any information concerning dual booting Solaris with Windows on a machine with standardized equipment. I have read on the sun.com page that it is possible and can even be pushed to the rear partition, but... (3 Replies)
Discussion started by: TStoddard
3 Replies

5. UNIX for Advanced & Expert Users

Dual Boot on HP-UX

Hy all Does anyone have Info on how to make a dual boot HP UX 10-20 HP UX 11 on a server ? Thanks in advance Olivier (3 Replies)
Discussion started by: Olivier
3 Replies

6. BSD

dual boot

I have recently installed free bsd on my windows xp laptop so that now it is a dual boot system. It worked fine for the first couple of days, but now whenever I try to boot into windows it hangs, giving the message WINDOWS\System32\DRIVERS\agp440.sys, bsd however, loads fine. I was wondering either... (3 Replies)
Discussion started by: elfhat
3 Replies

7. Solaris

solaris dual boot

hi ;) So I have 2 HDD (SATA and ATA). On the SATA I've installed WindwosXP and now I want to install solaris 10 on the ATA disk. Is it possible if the ATA disk is primary to make dual boot ? thank you very much (0 Replies)
Discussion started by: nocture
0 Replies

8. Linux

Dual-boot help

Does anyone know if it is possible to have a dual-boot machine with Linux (RH FC 5) and Unix (Solaris 10)? I currently have one OS (Linux RH FC 5) on one drive (master) and another OS (Unix - Solaris 10) on the other drive (slave). I am a little unsure of what to modify the grub.config file with,... (1 Reply)
Discussion started by: trmn8r
1 Replies

9. Emergency UNIX and Linux Support

Dual boot

Hi, I am having 1 TB hard disk and in that I have to install windows,linux 64 bit and linux 32 bit total 3 operating systems I need to install, how could I do that please help. I am having 64 bit machine h/w Thanks, Trimurtulu (5 Replies)
Discussion started by: ktrimu
5 Replies

10. Ubuntu

Do you dual-boot with other os

When I first started using Linux (Ubuntu) I decided to just do a full install. The PC I installed it on, was full of viruses and to be honest, I was never good handling them. So, I decided to just go for it and install. Anyways I got another computer recently, a much newer one and I decided to... (3 Replies)
Discussion started by: billcrosby
3 Replies
MAKECSD(1)						  The Canonical Csound Reference						MAKECSD(1)

NAME
makecsd - Creates a CSD file from the specified input files. . DESCRIPTION
Creates a CSD file from the specified input files. The first input file that has a .orc extension (case is not significant) is put to the <CsInstruments> section, and the first input file that has a .sco extension becomes <CsScore>. Any remaining files are Base64 encoded and added as <CsFileB> tags. An empty <CsOptions> section is always added. Some text filtering is performed on the orchestra and score file: o newlines are converted to the native format of the system on which makecsd is being run. o blank lines are removed from the beginning and end of files. o any trailing whitespace is removed from the end of lines. o optionally, tabs can be expanded to spaces with an user specified tabstop size. SYNTAX
makecsd [OPTIONS ... ] infile1 [ infile2 [ ... ]] INITIALIZATION
Flags: o - t n = expand tabs to spaces using tabstop size n (default: disabled). This applies only to the orchestra and score file. o - w n = set Base64 line width to n (default: 72). Note: the orchestra and score are not wrapped. o - o fname = output file name (default: stdout) EXAMPLES
makecsd -t 6 -w 78 -o file.csd file.mid file.orc file.sco sample.aif This creates a CSD from file.orc and file.sco (tabs are expanded to spaces assuming a tabstop size of 6 characters), and file.mid and sample.aif are added as <CsFileB> tags containing Base64 encoded data with a line width of 78 characters. The output file is file.csd. CREDITS
Author: Istvan Varga Jan 2003 AUTHORS
Barry Vercoe MIT Media Lab Author. Dan Ellis MIT Media Lab, Cambridge Massachussetts Author. COPYRIGHT
5.10 08/01/2011 MAKECSD(1)
All times are GMT -4. The time now is 07:22 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy