04-17-2007
If you must
Add a second hard drive to the system, large enough to hold /u for unix and D: for XP.
Check the CMOS settings for the primary drive and determine how many megabytes are available before you reach cylinder 1023. Change the geometry to suit using LBA or LARGE in order to achieve the required amount.
You will probably need about 2gb for each OS.
This should not be a problem, I checked my own 20gb disk and it has 2400 cylinders, so that it would have about 8gb before cylinder 1023.
Install XP on a partition that is only 4gb.
Install SCO on whatever remains on the primary drive, only /stand needs end before cylinder 1023.
If there is not enough room left for the SCO apps and data then partition the second hd with fdisk to provide one unix partition and one NTFS partition
On the XP side use the second hard disk as drive D and then when you install any applications, install them on D not C.
Make the unix partition active.
Then you should be able to type XP at the 'boot:' prompt and have XP run.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
i want to know how do i make my system a dual boot system for Linux 7.1 and Windows Nt 4.0 :( :confused: :confused: (2 Replies)
Discussion started by: mad2life
2 Replies
2. UNIX for Dummies Questions & Answers
Ok I had a windows and RH dual boot system and have now converted over completly to the linux system.
How do I regain the other half of my drive? I cannot see it in the disk manager. what do I do to format so that i can mount it? (1 Reply)
Discussion started by: macdonto
1 Replies
3. UNIX for Dummies Questions & Answers
Hi there!
I have a laptop which I plan on installing a dual boot on with Windows and Linux. I have Windows 98 installed at the moment, and I also have a copy of Slackware 8.
I talked to friend, and he said he had some problems installing a dual boot with linux on his laptop... So I just came... (2 Replies)
Discussion started by: satan404
2 Replies
4. UNIX for Dummies Questions & Answers
Greetings,
I have learned much since joining the message board, but I was unable to locate any information concerning dual booting Solaris with Windows on a machine with standardized equipment. I have read on the sun.com page that it is possible and can even be pushed to the rear partition, but... (3 Replies)
Discussion started by: TStoddard
3 Replies
5. UNIX for Advanced & Expert Users
Hy all
Does anyone have Info on how to make a dual boot
HP UX 10-20
HP UX 11
on a server ?
Thanks in advance
Olivier (3 Replies)
Discussion started by: Olivier
3 Replies
6. BSD
I have recently installed free bsd on my windows xp laptop so that now it is a dual boot system. It worked fine for the first couple of days, but now whenever I try to boot into windows it hangs, giving the message WINDOWS\System32\DRIVERS\agp440.sys, bsd however, loads fine. I was wondering either... (3 Replies)
Discussion started by: elfhat
3 Replies
7. Solaris
hi ;)
So I have 2 HDD (SATA and ATA). On the SATA I've installed WindwosXP and now I want to install solaris 10 on the ATA disk. Is it possible if the ATA disk is primary to make dual boot ?
thank you very much (0 Replies)
Discussion started by: nocture
0 Replies
8. Linux
Does anyone know if it is possible to have a dual-boot machine with Linux (RH FC 5) and Unix (Solaris 10)?
I currently have one OS (Linux RH FC 5) on one drive (master) and another OS (Unix - Solaris 10) on the other drive (slave).
I am a little unsure of what to modify the grub.config file with,... (1 Reply)
Discussion started by: trmn8r
1 Replies
9. Emergency UNIX and Linux Support
Hi,
I am having 1 TB hard disk and in that I have to install windows,linux 64 bit and linux 32 bit total 3 operating systems I need to install, how could I do that please help.
I am having 64 bit machine h/w
Thanks,
Trimurtulu (5 Replies)
Discussion started by: ktrimu
5 Replies
10. Ubuntu
When I first started using Linux (Ubuntu) I decided to just do a full install. The PC I installed it on, was full of viruses and to be honest, I was never good handling them. So, I decided to just go for it and install.
Anyways I got another computer recently, a much newer one and I decided to... (3 Replies)
Discussion started by: billcrosby
3 Replies
LEARN ABOUT SUSE
mkfs.bfs
MKFS.BFS(8) Linux System Administrator's Manual MKFS.BFS(8)
NAME
mkfs.bfs - make an SCO bfs filesystem
SYNOPSIS
mkfs.bfs [-N nr-of-inodes] [-V volume-name] [-F fsname] device [size-in-blocks]
DESCRIPTION
mkfs.bfs creates an SCO bfs file-system on a block device (usually a disk partition or a file accessed via the loop device).
The size-in-blocks parameter is the desired size of the file system, in blocks. If nothing is specified, the entire partition will be
used.
OPTIONS
-N Specify the desired number of inodes (at most 512). If nothing is specified some default number in the range 48-512 is picked
depending on the size of the partition.
-V volume-label
Specify the volume label. I have no idea if/where this is used.
-F fsname
Specify the fsname. I have no idea if/where this is used.
-v Be verbose.
EXIT CODES
The exit code returned by mkfs.bfs is 0 when all went well, and 1 when something went wrong.
SEE ALSO
mkfs(8).
AVAILABILITY
The mkfs.bfs command is part of the util-linux-ng package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux-ng/.
Util-linux 2.9x 12 Sept 1999 MKFS.BFS(8)