This will most likely be a real dumb question for a HP-UX admin, but here it goes anyhow.
lan0 - is up and configured
lan1 - is down, I want to bring it up.
lanconfig....ifconfig is there a difference?
My real question is, in solaris there is an /etc/hostname."?" file, is there a... (4 Replies)
I am trying to change an IP address on a machine running HPUX10
After I change it I can ping it from the outside but it completely locks the console. After a reboot it returns back to its previous IP. Any ideas??
Thanks
Brian (7 Replies)
hey,
I know that ifconfig on linux systems is identical to win ipconfig.
I wanted to know if there is a linux distribution (new or old) that uses the ipconfig command.
thanks alot :) (2 Replies)
Hi All,
I logged into a sun microsystems server box, using both a vnc session and a ssh session. I am able to use "ifconfig -a" in a ssh session, but the same on a vnc session says that its a invalid command. how is this possible, when i am logging into the same box through two different... (4 Replies)
Hi all,,i have problem with my homework form my lecture..
He is give me a homework to create:
ifconfig eth0 0.255.255.255 1.1.168.192
my lecture says, i can making the shell scripting to finish my homework..
i have question, can setting ifconfig like in the upper? (1 Reply)
Hi all,
I am getting some error messages during bootup
ifconfig :<hostname> bad address
and some more messages related to it.
I some how checked the /etc/hostanem.hme0 /etc/hosts file.
Entries in these files were proper.
If I am running the following command from root:
... (5 Replies)
Hi All,
I need some info on ifconfig.
ifconfig is available in Linux and Solaris. However the options available in Solaris is not there in Linux.
1. ifconfig -a == output is different in both OS. I am somewhat able to compare the output. But one thing I am not getting is after the flags... (2 Replies)
Unable to run the ifconfig in my home dir..
I did add adding /sbin and /usr/sbin in th PATH
But still unable to get that ..
Am using red hat linux
cat /etc/redhat-release
Red Hat Enterprise Linux Server release 5.3 (Tikanga) (3 Replies)
What would be the command to remove the IP address from an interface?
I want to remove the ip from this interface:
ce3: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 5
inet 155.216.13.74 netmask fffffff0 broadcast 155.216.13.79
ether 0:3:ba:da:a6:96 (3 Replies)
Discussion started by: Kjons76
3 Replies
LEARN ABOUT DEBIAN
edsc
EDSC(4) BSD Kernel Interfaces Manual EDSC(4)NAME
edsc -- Ethernet discard network interface
SYNOPSIS
device edsc
DESCRIPTION
The edsc interface is a software discard mechanism which may be used for performance analysis and software testing. It imitates an Ethernet
device, which allows for its use in conjunction with such drivers as if_bridge(4) and vlan(4).
As with other network interfaces, an edsc interface must have network addresses assigned for each address family with which it is to be used.
These addresses may be set or changed with the SIOCSIFADDR ioctl(2) or ifconfig(8) utility.
Each edsc interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the
cloned_interfaces variable in rc.conf(5).
SEE ALSO ioctl(2), arp(4), if_bridge(4), inet(4), intro(4), vlan(4), rc.conf(5), arp(8), ifconfig(8)HISTORY
The edsc device was derived from the disc(4) device and first appeared in FreeBSD 6.3. This manpage was adapted from disc(4).
CAVEATS
Since outgoing packets are just discarded by edsc, ARP requests stay unreplied. Consequently, an IP packet cannot be sent via edsc until a
static arp(4) entry is created for its next hop using arp(8).
Initially an edsc interface has a zero link level address. It can be changed with ifconfig(8) lladdr if needed.
BSD March 25, 2007 BSD