04-07-2007
ifconfig <interfacename> in most cases
8 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
All,
I have a need to software change the MAC address of a NIC in a Sparc Ultra 10 - I believe there is a command that allows to do this at boot up?
Is it a missing (to me) part of ifconfig ?
If so, what is the syntax?
All replies gratefully received !
Thanks
Andrew (3 Replies)
Discussion started by: wretch
3 Replies
2. IP Networking
I have a SCO OpenServer 5.0.5 and my cuestion is can i have 2 ip address in one nic?, how?.
Thanks. (1 Reply)
Discussion started by: dvl
1 Replies
3. IP Networking
Hi,
I bound a virtual IP to a network card on my E450 server and I am getting this error when I reboot the server, saying, " retrying host, RPC time out. I had to break this sequence and allow other services to load. Of course they didn't load properly. Please how can I sort this out? I do need... (8 Replies)
Discussion started by: Ronny
8 Replies
4. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
5. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
6. Windows & DOS: Issues & Discussions
Anyone ever see the NIC get a mac of 00-00-00-00-00-00?
Changing it in driver advanced tab didn't stick. Used macshift and gave it a random one. Best guess I had is it lost its eprom. It was an issues on my dads pc I stopped by after work so I wasn't able to boot a proper OS to further diagnose.
... (0 Replies)
Discussion started by: neutronscott
0 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT DEBIAN
rgephy
RGEPHY(4) BSD Kernel Interfaces Manual RGEPHY(4)
NAME
rgephy -- RealTek RTL8168/8169/8110/8211 series 10/100/1000 Gigabit Ethernet PHY driver
SYNOPSIS
To compile all available PHY drivers into the kernel, place the following line in your kernel configuration file:
device miibus
Alternatively, to selectively compile this driver into the kernel, place the following lines in your kernel configuration file instead:
device mii
device rgephy
DESCRIPTION
The rgephy driver supports the RealTek RTL8168, RTL8169, RTL8110 and RTL8211 series integrated 10/100/1000 Gigabit Ethernet PHYs.
In order to get a list of media types and options supported by a specific instance of the rgephy driver, run ifconfig -m on the instance of
its parent MAC driver.
Additionally, the rgephy driver supports the following special media option:
flag0 When manually setting media type and options via ifconfig(8), the rgephy driver by default also triggers an autonegotiation advertis-
ing the selected media. This is done in order to work around hardware issues in certain scenarios. It is believed that this behavior
does not cause harm in general but in fact can have an adverse effect in edge cases. In order to manually set the media type and
options without also triggering an autonegotiation, the rgephy driver allows to turn this behavior off via the flag0 media option.
Note that this special media option will not show up in the output of ifconfig(8), even when set.
EXAMPLES
Manually set 100BASE-TX full-duplex without also triggering an autonegotiation:
ifconfig re0 media 100baseTX mediaopt full-duplex,flag0
SEE ALSO
intro(4), miibus(4), ifconfig(8)
BSD
January 16, 2011 BSD