Sponsored Content
Full Discussion: Link Aggregation and LACP
Top Forums UNIX for Advanced & Expert Users Link Aggregation and LACP Post 302113453 by reborg on Friday 6th of April 2007 06:45:57 AM
Old 04-06-2007
hcclnoodles

No duplicate or cross-posting.
 

10 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. IP Networking

bonding lacp and link aggregation

Hello, I am trying to get clarity on a few things and am looking for some info. In every article I have read about link aggregation and lacp, it can be used combine physical links to create 1 logical link for increased bandwidth. But what it doesn't say is if this is limited by source/dst. ... (1 Reply)
Discussion started by: jaredo
1 Replies

3. IP Networking

LACP aggregation on separates switches

Hello, I'm working on LACP architecture. I would like to know if it's possible to aggregate two links on two separate switches. Here an example I want : Aggregation of link1 and link2 to obtain a logical 2 gbit/s link. Also have redundancy, if one of them is down, the traffic goes through the... (1 Reply)
Discussion started by: jbemonet
1 Replies

4. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

5. HP-UX

Link Aggregation HPUX

Hi, Hoping someone can offer some advice on something i have not dealt with before. We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies

6. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

7. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

8. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies

10. Solaris

How can I test link aggregation?

Hi, I have Solaris-10 server and link aggregation is configured on this in below way # dladm show-aggr key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto) device address speed duplex link state bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
Child::Link::IPC::Pipe::Proc(3pm)			User Contributed Perl Documentation			 Child::Link::IPC::Pipe::Proc(3pm)

NAME
Child::Link::IPC::Pipe::Proc - Proc object used by the pipe plugin. SEE ALSO
This class inherits from: Child::Link::Proc Child::Link::IPC Child::Link::IPC::Pipe HISTORY
Most of this was part of Parrallel::Runner intended for use in the Fennec project. Fennec is being broken into multiple parts, this is one such part. FENNEC PROJECT
This module is part of the Fennec project. See Fennec for more details. Fennec is a project to develop an extendable and powerful testing framework. Together the tools that make up the Fennec framework provide a potent testing environment. The tools provided by Fennec are also useful on their own. Sometimes a tool created for Fennec is useful outside the greator framework. Such tools are turned into their own projects. This is one such project. Fennec - The core framework The primary Fennec project that ties them all together. AUTHORS
Chad Granum exodist7@gmail.com COPYRIGHT
Copyright (C) 2010 Chad Granum Child is free software; Standard perl licence. Child is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the license for more details. perl v5.10.1 2011-03-07 Child::Link::IPC::Pipe::Proc(3pm)
All times are GMT -4. The time now is 07:09 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy