Sponsored Content
Operating Systems HP-UX Add Route on HP-UX v10.x, help. Post 302113367 by Perderabo on Thursday 5th of April 2007 01:08:12 PM
Old 04-05-2007
I'm not sure what it is you're trying to do, you seem to have two theories. To add a route to the 192.168.80.0 network that uses 10.10.10.13, I think it is:

route add net 192.168.80.0 255.255.255.0 10.10.10.13 1

But I don't have access to a 10.x box to test it.
 

10 More Discussions You Might Find Interesting

1. AIX

route add

Hello , We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ... #route add server.ip router.ip after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies

2. IP Networking

Do I need to add a route??

I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0. My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network. My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies

3. IP Networking

Route add probleme

I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system. The ip i am trying to get to is 172.16.4.48 I need to get to it via the hme1 interface. The vpn gateway has this ip 172.30.50.1 I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies

4. Solaris

Route Add

Hi, I am trying to add route command in Solaris 10 machine in the following fashion: route add -host 10.8.112.10 180.144.1.250 -interface lo0:1 this command fails with an error "lo0:1: bad value" I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies

5. IP Networking

route add

I have built a new linux server, via a iLo connection. and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty. Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies

6. Solaris

Add route to solaris10

Hi need to add 2 routes, one on each server. I know the route add comand but I have always been given the parameters to put in. I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ? In... (6 Replies)
Discussion started by: vettec3
6 Replies

7. Solaris

Add route to solaris 10

I need to add a new route on solaris10 machine. I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway. How I do ? Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies

8. AIX

Default Route add fails

AIX version 5.3 when I try to add default gateway # route add 0 192.168.100.254 Or # route add default 192.168.100.254 I get the error 0821-275 route: socket: The file access permissions do not allow the specified action. searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies

9. Solaris

Couldn't add route on Solaris 10

Hi Solaris Experts, I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node # netstat -rnv IRE Table: IPv4 Destination Mask Gateway Device Mxfrg Rtt Ref Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies

10. IP Networking

Add explicit route

Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254 if not working, please try gateway through management port: 10.128.55.254 Just want to double confirm if this would be the correct command #route add -net 10.128.255.41/32 10.128.201.254 And if didnt work #route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
oidentd_masq.conf(5)						File Formats Manual					      oidentd_masq.conf(5)

NAME
oidentd_masq.conf - oidentd IP masquerading/NAT configuration file. DESCRIPTION
If you are using IP masquerading or NAT, oidentd can optionally return a username for connections from other machines. Support for this is specified by calling oidentd with the -m (or --masq) flag and by creating an /etc/oidentd_masq.conf file. oidentd can also forward requests for an IP masqueraded connection to the machine from which connection originates by way of the -f option. This will only work if the host to which the connection is forwarded is running oidentd with the -P (proxy) flag, or if the host's ident daemon will return a valid reply regardless of the input supplied by and the address of the host requesting the info (some ident daemons for windows do this, maybe others). FORMAT
<IP Address|Hostname>[/<Mask>] <Ident Response> <System Type> The first field contains the IP address or the hostname of a machine that IP masquerades through the machine on which oidentd runs. The mask parameter can be either a network mask or a mask in CIDR notation. A mask of 24 is equivalent to 255.255.255.0, a mask of 16 is equivalent to 255.255.0.0, etc. The second field specifies the reply that oidentd will return for lookups to the host matching the IP address specified in the first param- eter. The third field specifies the operating system the machine matching the first parameter is running. EXAMPLES
<Host>[/<Mask>] <Ident Response> <System Type> 192.168.1.1 someone UNIX 192.168.1.2 noone WINDOWS 192.168.1.1/32 user1 UNIX 192.168.1.0/24 user3 UNIX 192.168.0.0/16 user4 UNIX somehost user5 UNIX 192.168.1.0/255.255.255.0 user6 UNIX AUTHOR
Ryan McCabe <ryan@numb.org> http://dev.ojnk.net SEE ALSO
oidentd(8) oidentd.conf(5) version 2.0.8 13 Jul 2003 oidentd_masq.conf(5)
All times are GMT -4. The time now is 07:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy