04-05-2007
I'm not sure what it is you're trying to do, you seem to have two theories. To add a route to the 192.168.80.0 network that uses 10.10.10.13, I think it is:
route add net 192.168.80.0 255.255.255.0 10.10.10.13 1
But I don't have access to a 10.x box to test it.
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
7. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
8. AIX
AIX version 5.3
when I try to add default gateway
# route add 0 192.168.100.254
Or
# route add default 192.168.100.254
I get the error
0821-275 route: socket: The file access permissions do not allow the specified action.
searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)
NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO
vconfig(8) interfaces(5)
vlan September 30 2007 VLAN-INTERFACES(5)