04-05-2007
Add Route on HP-UX v10.x, help.
Hi,
My H-UX box has the GW pointing to 10.10.10.1 and I need add it a new route pointing to 192.168.80.x with the GW 10.10.10.13
I tried with:
#route add 192.168.80.2 255.255.255.255 10.10.10.13
but I get: add net 192.168.80.0: gateway 255.255.255.0: Network is unreachable
I tried with
#route add 192.168.80.2 10.10.10.13
netstar -rn:
192.168.80.2 10.10.10.13 UH 0 0 lan0 1500
but I can reach it, when I exec a traceroute 192.168.80.2, it uses the GW 10.10.10.1 instead of 10.10.10.13
What am I doing wrong? I've tried on WinXP and it works OK.
Thanks....
10 More Discussions You Might Find Interesting
1. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
2. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
3. IP Networking
I have a system that i want to reach via a vpn created vi a fierwall.The fierwall in an other system.
The ip i am trying to get to is 172.16.4.48
I need to get to it via the hme1 interface.
The vpn gateway has this ip 172.30.50.1
I need to clean up the routing table and make this work; or is it... (5 Replies)
Discussion started by: waterboy
5 Replies
4. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
5. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
6. Solaris
Hi need to add 2 routes, one on each server.
I know the route add comand but I have always been given the parameters to put in.
I need a route in each of the 2 following servers to be able to ping and ssh between them. But how do i know which netmask to put in the route add command ?
In... (6 Replies)
Discussion started by: vettec3
6 Replies
7. Solaris
I need to add a new route on solaris10 machine.
I want that all traffic on the 23 port (telnet) use 192.168.200.1 gateway.
How I do ?
Thank you in advance. (1 Reply)
Discussion started by: arfry
1 Replies
8. AIX
AIX version 5.3
when I try to add default gateway
# route add 0 192.168.100.254
Or
# route add default 192.168.100.254
I get the error
0821-275 route: socket: The file access permissions do not allow the specified action.
searching on google i came across similar... (5 Replies)
Discussion started by: filosophizer
5 Replies
9. Solaris
Hi Solaris Experts,
I am trying to add a routing table entry on our 5.1 Generic_144488-12 sun4v sparc Solaris 10 SUNW,SPARC-Enterprise-T5220 so that it is possible to ping 10.56.9.34 node
# netstat -rnv
IRE Table: IPv4
Destination Mask Gateway Device Mxfrg Rtt Ref
Flg Out In/Fwd ... (2 Replies)
Discussion started by: gjackson123
2 Replies
10. IP Networking
Add explicit route to 10.128.255.41/32 , gateway: 10.128.201.254
if not working, please try gateway through management port: 10.128.55.254
Just want to double confirm if this would be the correct command
#route add -net 10.128.255.41/32 10.128.201.254
And if didnt work
#route add... (1 Reply)
Discussion started by: Thilagarajan
1 Replies
LEARN ABOUT NETBSD
route.conf
ROUTE.CONF(5) BSD File Formats Manual ROUTE.CONF(5)
NAME
route.conf -- static routes config file
DESCRIPTION
The route.conf file is read by the staticroute rc.d script during system start-up and shutdown, and is intended for adding and removing
static routes.
FILE FORMAT
Lines starting with a hash ('#') are comments and ignored. Lines starting with a plus sign ('+') are run during start-up, while lines start-
ing with a minus sign ('-') are run during system shutdown. If a line starts with a '!', the rest of the line will get evaluated as a shell
script fragment. All other lines are passed to route(8). During start-up, they are passed behind a ``route add -'' command and during shut-
down behind a ``route delete -'' command.
FILES
/etc/route.conf The route.conf file resides in /etc.
/etc/rc.d/staticroute
rc.d(8) script that parses route.conf.
EXAMPLES
In this example, the interface for the desired routing changes is set, the IP address on that interface is determined, and a route is added
during startup, or deleted during system shutdown.
# Set interface and determine current IP address for added route.
!ifname=bnx0
!ipaddr=$(/sbin/ifconfig ${ifname} | awk '$1 == "inet" {print $2}')
net 10.10.1 -interface ${ipaddr}
In this example, IP forwarding is turned on during start-up, and a static route added for 192.168.2.0. During system shutdown, the route is
removed and IP forwarding turned off.
# Turn on/off IP forwarding.
+sysctl -w net.inet.ip.forwarding=1
-sysctl -w net.inet.ip.forwarding=0
net 192.168.2.0 -netmask 255.255.255.0 192.168.150.2
SEE ALSO
rc.conf(5), rc(8), route(8)
BSD
May 1, 2012 BSD