04-05-2007
I have never tried that, but I would expect it work. The adjective "separate" would not apply to trunked switches. If you try it, let us know if it works and which protocol was used to trunk the switches.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
2. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
7. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
8. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT DEBIAN
flow-gen
flow-gen(1) General Commands Manual flow-gen(1)
NAME
flow-gen -- Generate test flows
SYNOPSIS
flow-gen [-h] [-b big|little] [-d debug_level] [-n count] [-V version] [-z z_level]
DESCRIPTION
The flow-gen utility generates a test pattern of flows in any of the currently supported export versions typically for debugging purposes.
OPTIONS
-b big|little
Byte order of output.
-d debug_level
Enable debugging.
-h Display help.
-n count Generate count flows. Default 1000.
-V version
Generate version type exports. Supported versions are:
1 NetFlow version 1 (No sequence numbers, AS, or mask)
5 NetFlow version 5
6 NetFlow version 6 (5+ Encapsulation size)
7 NetFlow version 7 (Catalyst switches)
8.1 NetFlow AS Aggregation
8.2 NetFlow Proto Port Aggregation
8.3 NetFlow Source Prefix Aggregation
8.4 NetFlow Destination Prefix Aggregation
8.5 NetFlow Prefix Aggregation
8.6 NetFlow Destination (Catalyst switches)
8.7 NetFlow Source Destination (Catalyst switches)
8.8 NetFlow Full Flow (Catalyst switches)
8.9 NetFlow ToS AS Aggregation
8.10 NetFlow ToS Proto Port Aggregation
8.11 NetFlow ToS Source Prefix Aggregation
8.12 NetFlow ToS Destination Prefix Aggregation
8.13 NetFlow ToS Prefix Aggregation
8.14 NetFlow ToS Prefix Port Aggregation
1005 Flow-Tools tagged version 5
-z z_level
Configure compression level to z_level. 0 is disabled (no compression), 9 is highest compression.
EXAMPLES
Generate a test pattern of 1000 version 5 flows and send them in the Cisco NetFlow packet format to 10.0.0.1 port 9500.
flow-gen -V5 | flow-send 0/10.0.0.1/9500
BUGS
The test pattern may change between releases.
AUTHOR
Mark Fullmer maf@splintered.net
SEE ALSO
flow-tools(1)
flow-gen(1)