04-05-2007
I have never tried that, but I would expect it work. The adjective "separate" would not apply to trunked switches. If you try it, let us know if it works and which protocol was used to trunk the switches.
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Hi there
I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question
Ive seen multiple websites that say the following
Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies
2. Solaris
Hi everybody,
One client asked me to configure network failover and load balancing for two Ethernet interfaces, I tried IPMP but I was unable to do so, because he's using his Gateway as firewall and PING is disabled.
so IPMP kept telling me that all interfaces failed because gateway can't be... (8 Replies)
Discussion started by: Sun Fire
8 Replies
3. IP Networking
I have some linux machines that I am trying to increase the throughput to on a single connection. They connect to a switch with two 1GbE lines and the switch does not have Link Aggregation support for these machines. I have tried bonding with balance-rr, balance-alb, but the machines can only... (4 Replies)
Discussion started by: Eruditass
4 Replies
4. AIX
Hi,
I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies
5. HP-UX
Hi,
Hoping someone can offer some advice on something i have not dealt with before.
We have a server that seems to have some very strange configuration done on it. It has 2 physical NIC's and rather than both be aggregated into LAN900 we have 1 in LAN900 and 1 in LAN901? (See Below)... (2 Replies)
Discussion started by: Andyp2704
2 Replies
6. Solaris
Me again :)
I'm trying to find a page describing the L2, L3 und L4 modes of dladm.
It's nice to read "hashed by ip header", but how should I use that?
On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies
7. HP-UX
Hi,
I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900.
Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server.
So It need to change in cluster script.
But I dont know where I have to change it.
Please... (1 Reply)
Discussion started by: mkiron
1 Replies
8. Solaris
Hi,
I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP?
I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies
9. IP Networking
Hi
ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ?
are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
10. Solaris
Hi,
I have Solaris-10 server and link aggregation is configured on this in below way
# dladm show-aggr
key: 1 (0x0001) policy: L4 address: 3c:d9:2b:ee:a8:a (auto)
device address speed duplex link state
bnx1 3c:d9:2b:ee:a8:a... (8 Replies)
Discussion started by: solaris_1977
8 Replies
LEARN ABOUT CENTOS
ibcacheedit
IBCACHEEDIT(8) Open IB Diagnostics IBCACHEEDIT(8)
NAME
IBCACHEEDIT -
edit an ibnetdiscover cache
SYNOPSIS
ibcacheedit [options] <orig.cache> <new.cache>
DESCRIPTION
ibcacheedit allows users to edit an ibnetdiscover cache created through the --cache option in ibnetdiscover(8) .
OPTIONS
--switchguid BEFOREGUID:AFTERGUID
Specify a switchguid that should be changed. The before and after guid should be separated by a colon. On switches, port guids are
identical to the switch guid, so port guids will be adjusted as well on switches.
--caguid BEFOREGUID:AFTERGUID
Specify a caguid that should be changed. The before and after guid should be separated by a colon.
--sysimgguid BEFOREGUID:AFTERGUID
Specify a sysimgguid that should be changed. The before and after guid should be spearated by a colon.
--portguid NODEGUID:BEFOREGUID:AFTERGUID
Specify a portguid that should be changed. The nodeguid of the port (e.g. switchguid or caguid) should be specified first, followed
by a colon, the before port guid, another colon, then the after port guid. On switches, port guids are identical to the switch
guid, so the switch guid will be adjusted as well on switches.
Debugging flags
-h, --help show the usage message
-V, --version show the version info.
AUTHORS
Albert Chu
< chu11@llnl.gov >
IBCACHEEDIT(8)