Sponsored Content
Full Discussion: lan card not detecting
Operating Systems SCO lan card not detecting Post 302113018 by bidhayakm on Tuesday 3rd of April 2007 01:50:58 AM
Old 04-03-2007
lan card not detecting

hi all
i have installed SCO 5.0.5 on a "Netfinity 5000" IBM server. But the OS is not detecting the lan card. how can i detect it.... help and thanks in advance .
bidhayak
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

LAN Card Problem !

The Lan card in one of our UIII WS's seem doesn't work,so with ping command i can not see any of the machines in LAN and with some other tests i'm sure it's not OK. I tried to use the second card on PCI port ,but the replaced card was one of the ordinary card for PC's ...by the way after... (1 Reply)
Discussion started by: nikk
1 Replies

2. Cybersecurity

lan card autonegotiation?

what is lan card autonegotiation ? how to enable and disable this feature? (2 Replies)
Discussion started by: nabil_boussetta
2 Replies

3. SCO

LAN card problem

Dear all Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working. Is... (1 Reply)
Discussion started by: ccvyas
1 Replies

4. UNIX for Dummies Questions & Answers

Detecting Network Card in Solaris10

I have an E420 server that has a TPE Slot / NIC installed. However there is no interface file installed eg /etc/hostname.hme0 or equivalent. I have placed a private ip entry int the hosts file to accompany the loop back entry i.e. 127.0.0.1 localhost 172.16.0.10 loghost se420 ... (2 Replies)
Discussion started by: jimthompson
2 Replies

5. Programming

LAN card status Information

Please tell me API in Solaris / Linux / UNIX to get status information of LAN card. (1 Reply)
Discussion started by: mansoorulhaq
1 Replies

6. Linux

How to check the LAN card?

Hi. I have a lan card installed on my server. I want to check the duplex speed of it. How can I check it? Help is appreciated. Thank you. (3 Replies)
Discussion started by: Amol21
3 Replies

7. Solaris

Can't ping new PCI LAN card x4270_m2

Hi, I've recently moved my pci LAN card from Slot2 Slot5 on my sun x4270_m2 server (solaris 10). I've done the touch / reconfigure and devfsadm, however my issue is that im able to configure the e1000g7 port with an ip address (192.168.0.1) but if i plug my laptop (set with static ip... (7 Replies)
Discussion started by: kerrygold
7 Replies

8. Linux

Lan card not reaching Gateway

Hi, I have this problem on RHEL box. I am using two NIC's of same model and make (Intel 82557) in the adjacent PCI slots . I am using each one for different subnet and have assigned them ipaddresses and gateways of respective subnets . While one is O.K. connecting to its ... (5 Replies)
Discussion started by: dextergenious
5 Replies

9. Red Hat

Linux Red Hat AS3 Network card is not detecting ...

Dear Expert, I 've installed Redhat linux AS3, My machine having Inbuild network card (Intel(R) 82566DM-2 Gigabit Network Connection). I've downloaded e1000e-2.3.2 from Intel site, but its not working for my machine. I'm unable to configure the Network. ifconfig eth0 xx.xx.xx.xx netmask... (0 Replies)
Discussion started by: Mohammed Faiz
0 Replies

10. Red Hat

PC cannot reach two lan card Linux box

we have red hat 6 linux box There are two lan card one lan card eth0 have ip 10.82.190.31/24 GW 10.82.190.254 2th lan card eth1 have ip 10.82.188.33/24 GW 10.82.188.254 I have below route ... I use two route table root@xxx# netstat -rn Kernel IP routing table Destination Gateway ... (5 Replies)
Discussion started by: chuikingman
5 Replies
DAIC(4) 						   BSD Kernel Interfaces Manual 						   DAIC(4)

NAME
daic -- isdn4bsd driver for EICON.Diehl active ISDN cards SYNOPSIS
daic0 at isa? iomem 0xd8000 irq 10 DESCRIPTION
The daic driver supports the old Diehl active cards: S, SX, SXn, SCOM and QUADRO. For a QUADRO card, the driver will detect the board type and use all four ports, each attached as a controller of its own to the isdn4bsd system, which can be listed using the daicctl utility. The daic driver interfaces the ISDN card to the ISDN4BSD kernel subsystem. All lower layer ISDN control is handled by the card. This should allow you to run any national ISDN protocol delivered by EICON.Diehl for your card, but the driver has only been tested with the DSS1 proto- col and some parts of the cards interface are ISDN protocol dependent. The daic driver is written to conform to the software interface documented by Diehl in their ISDN-Karten Benutzerhandbuch from 1992. MICROCODE DOWNLOAD
Every active card needs its own operating software before it can work. You have to download this to the card before using it with isdn4bsd. Use the daicctl utility to do this, i.e. call daicctl -d te_etsi.sx 1 to download the file te_etsi.sx to controller number 1. Use daicctl -l to list all available controllers (and ports). You have to select the correct ISDN protocol file for your ISDN interface, see the Diehl docu- mentation for details. The cards bootstrap process involves another file, which is independent of the card type you use and the protocol you run. It is called download.bin in current versions of the Diehl software distribution and has to be copied to the kernel compile directory under dev/microcode/daic and converted into a header file used when compiling the kernel by running make in that directory. Your kernel compile will fail and remind you of this if you forget to do this. Due to copyright restrictions we cannot distribute the driver with this file inte- grated. But if you own a card, you do have the file (or can get it from the Diehl web server). SEE ALSO
daicctl(1) BUGS
The driver is not yet finished. BSD
January 30, 1998 BSD
All times are GMT -4. The time now is 02:05 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy