03-30-2007
Hi zazzybob, the route command solved my issue. thank you.
9 More Discussions You Might Find Interesting
1. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
2. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
3. UNIX for Dummies Questions & Answers
Hi Guys,
is there a way to send traffic coming from the source iface (eth0, eth1)? i need to test traffic that will come from both eth0 and eth1 from a Linux box.
Thanks,
Martin (0 Replies)
Discussion started by: mdap
0 Replies
4. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
5. UNIX for Dummies Questions & Answers
Right now I have a computer that I want to use as the monitor for my network. It's currently running Windows 7, and so as I understand it the NIC won't monitor all the traffic on the network. So my question is, if I install Linux on this computer will I be able to force the NIC card into... (1 Reply)
Discussion started by: iJeydon
1 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
routes(4) Kernel Interfaces Manual routes(4)
NAME
routes - Specifies Internet routing information to the routing tables
SYNOPSIS
/etc/routes
DESCRIPTION
Static routes can be defined in the /etc/routes file. The /etc/routes file identifies static routes that are automatically added to the
network routing tables with the /usr/sbin/route add command. The /sbin/init.d/route script contains the /usr/sbin/route add command that
is executed for each entry in the /etc/routes file when the network is restarted on the system or the system is rebooted.
The general format of an entry in the /etc/routes file is: Dest Name1 Name2
The following is a brief description of each element in an /etc/routes file entry: A keyword that indicates whether the route is to a net-
work or to a host. The two possible keywords are -net and -host. The name or address of the destination network or host. Name1 can be
either a symbolic name (as used in the /etc/hosts or /etc/networks file) or an Internet address specified in dotted-decimal format. The
name or address of the gateway host to which messages should be forwarded. Name2 can be either a symbolic name (as used in the /etc/hosts
file) or an Internet address specified in dotted-decimal format.
The routes file is a Context-Dependent Symbolic Link (CDSL) and must be maintained as such. See the System Administration manual for more
information.
EXAMPLES
To specify a route to a network through a gateway host with an entry in the /etc/routes file, enter:
-net net2 host4
This example specifies a route to a network, net2, through the gateway host4. To specify a route to a host through a gateway host
with an entry in the /etc/routes file, enter:
-host host2 host4
This example specifies a route to a host, host2, through the gateway host4. To specify a route to a default gateway host with an
entry in the /etc/routes file, enter:
default 130.9.0.5
This example specifies a route to a default gateway with an Internet address of 130.9.0.5.
FILES
Contains the /usr/sbin/routed add command.
RELATED INFORMATION
Commands: route(8)
Daemons: gated(8), routed(8)
Files: gated.conf(4)
Network Administration delim off
routes(4)