Sponsored Content
Full Discussion: network driver cpu usage
Operating Systems Solaris network driver cpu usage Post 302112026 by reborg on Saturday 24th of March 2007 01:36:51 PM
Old 03-24-2007
What type of network traffic is it?

If you are dealing with a lot of encrypted traffic, you could probably do something more efficient...ie offload to the crypto accelerator, because you may be seeing a problem related to FPU queuing, rather than actual CPU load.
 

10 More Discussions You Might Find Interesting

1. Programming

Monitor CPU usage and Memory Usage

how can i monitor usages of CPU, Memory, Hard disk etc. under SUN Solaries through a c program or java program i want to store that data into database so i can show it graphically thanks in advance (2 Replies)
Discussion started by: Gajanad Bihani
2 Replies

2. Programming

Network device driver

HI, I am writing a network device driver for RTL8139c card on 2.6.18 kernel ... I am facing few queries listed below 1. Can i able to at all write a driver for RTL8139C or Realtek had designed new chip for 2.6 series kernel? 2. If no then which driver file 2.6.18 uses .. Is it 8139too.c or... (1 Reply)
Discussion started by: niketan
1 Replies

3. Programming

CPU usage and memory usage

Please tell me solaris functions/api for getting following information 1- Function that tells how much memory used by current process 2- Function that tells how much memory used by all running processes 3- Function that tells how much CPU is used by current process 4- Function that tells how... (1 Reply)
Discussion started by: mansoorulhaq
1 Replies

4. HP-UX

how can I find cpu usage memory usage swap usage and logical volume usage

how can I find cpu usage memory usage swap usage and I want to know CPU usage above X% and contiue Y times and memory usage above X % and contiue Y times my final destination is monitor process logical volume usage above X % and number of Logical voluage above can I not to... (3 Replies)
Discussion started by: alert0919
3 Replies

5. Solaris

current CPU usage, memory usage, disk I/O oid(snmp)

Hi, I want to monitor the current cpu usage, monitor usage , disk I/o and network utlization for solaris using SNMP. I want the oids for above tasks. can you please tell me that Thank you (2 Replies)
Discussion started by: S_venkatesh
2 Replies

6. Solaris

Installing Network on Computer, might be driver

Hi All, Just completing my second Solaris installation, in the previous one which was on a Dell X64 machine, I went through the Network configuration setting, on the current computer which I am installing Solaris on, its a custom built machine and for some reason, I didnt see the screen where I... (1 Reply)
Discussion started by: platforminc
1 Replies

7. Solaris

Multi CPU Solaris system shows 100% CPU usage.

Hello Friends, On one of my Solaris 10 box, CPU usage shows 100% using "sar", "vmstat". However, it has 4 CPUs and prstat and glance are not showing enough processes to justify high CPU utilization. ========================================================================= $ prstat -a ... (4 Replies)
Discussion started by: mahive
4 Replies

8. AIX

How to monitor the IBM AIX server for I/O usage,memory usage,CPU usage,network..?

How to monitor the IBM AIX server for I/O usage, memory usage, CPU usage, network usage, storage usage? (3 Replies)
Discussion started by: laknar
3 Replies

9. Programming

The simplest network driver

Hi, I am trying to write the simplest network driver that would send whatever through cable. My configuration is: Linux machine with some Intel network adapter Another machine with WireShark I connected Intel network adapter to second machine and want anything to pop up at wireshark. ... (12 Replies)
Discussion started by: Chrisdot
12 Replies

10. AIX

High Runqueue (R) LOW CPU LOW I/O Low Network Low memory usage

Hello All I have a system running AIX 61 shared uncapped partition (with 11 physical processors, 24 Virtual 72GB of Memory) . The output from NMON, vmstat show a high run queue (60+) for continous periods of time intervals, but NO paging, relatively low I/o (6000) , CPU % is 40, Low network.... (9 Replies)
Discussion started by: IL-Malti
9 Replies
aoe-interfaces(8)					      System Manager's Manual						 aoe-interfaces(8)

NAME
aoe-interfaces - restrict aoe driver to specified network interfaces SYNOPSIS
aoe-interfaces [dev1] [dev2 ...] aoe-interfaces -c DESCRIPTION
The aoe-interfaces command tells the aoe driver to ignore ATA over Ethernet (AoE) traffic on all but the specified network interfaces. It is analogous to the aoe_iflist module load option. If neither the aoe_iflist module load option nor the aoe-interfaces command are used, the aoe driver will use any network interface for AoE traffic. Using aoe-interfaces to limit AoE to only trusted networks prevents the case where a rogue AoE target appears on a public net- work, diverting data from the legitimate AoE target. Such an imposter target effectively corrupts the data on the legitimate target. If the aoe driver is a module, then calling aoe-interfaces without arguments will display the current interfaces list. If it hasn't been set then the output will be blank. It's good to run the aoe-discover command after setting the AoE interfaces list. OPTIONS
-c The -c flag will clear the interface access list, permitting any interface to be used. EXAMPLE
In this example, the root user on a host named nai loads the aoe module with only eth0 allowable for AoE traffic. After remembering that shelf 7 is on eth3, this sysadmin uses aoe-interfaces to add eth3 to the list of allowable network interfaces and then calls aoe-discover to ask the aoe driver to look for new AoE devices. nai:~# modprobe aoe aoe_iflist="eth0" nai:~# aoe-stat e10.9 eth0 up nai:~# aoe-interfaces eth0 eth3 nai:~# aoe-discover nai:~# aoe-stat e7.0 eth3 up e7.1 eth3 up e7.2 eth3 up e7.3 eth3 up e7.4 eth3 up e7.5 eth3 up e7.6 eth3 up e7.7 eth3 up e7.8 eth3 up e7.9 eth3 up e10.9 eth0 up nai:~# aoe-interfaces eth0 eth3 SEE ALSO
aoe-discover(8), aoe-stat(8), aoetools(8). AUTHOR
Ed L. Cashin (ecashin@coraid.com) aoe-interfaces(8)
All times are GMT -4. The time now is 12:09 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy