03-06-2007
No, the Blade 150 also suffers from the 48-bit LBA barrier and has a 127GB limit.
Therefore 2x 120GB is maximum, even with a PCI IDE controller.
10 More Discussions You Might Find Interesting
1. UNIX Desktop Questions & Answers
I have a cuestion. How Can I to add other hard disk to my computer? I need to configurate anyone? (4 Replies)
Discussion started by: hmaraver
4 Replies
2. AIX
Hello
I am trying to format an extra hard disk, I want to purge all data. Does any one know how to do this, I found a format command but it only works for floppies , also related to do this how do you defrag ? I am running AIX 5.3
Thanks (1 Reply)
Discussion started by: mrmeswani
1 Replies
3. AIX
Hello everyone
I got several aix boxes with aix 5.3
I got a ibm san ds4500
My question is
How can I do a match between my disks on aix and the san?
I try to do a match with the LUN but for example. In my san I got several 1 LUN and on one of my aix box I got this
If I type lscfg... (4 Replies)
Discussion started by: lo-lp-kl
4 Replies
4. UNIX for Dummies Questions & Answers
:eek: I use this Solaris to run CMS a call acounting software package for my job. No one could run reports today because it said the this when you logged on
"The following file systems are low, and could adversely affect server performance:
File system /: 99%full"
Can some one please explain... (9 Replies)
Discussion started by: mannyisme
9 Replies
5. SCO
Is SATA hard disk is suooprted by SCO OpenServer 5.05? If No, how to couter this problem. If yes, please provide the installation steps. (2 Replies)
Discussion started by: rakeshkumar9919
2 Replies
6. Solaris
I purchased a Sunblade 150 from Ebay. It had 512MB RAM and 80GB hard disk. I recently purchased additional RAM and another 80GB disk, and installed them. The RAM goes through POST without issues. I just can't get beyond the OK prompt. I am using the serial console.
I have been unable to... (5 Replies)
Discussion started by: Geekasaurus
5 Replies
7. SCO
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Discussion started by: ccc
3 Replies
8. Red Hat
When we write a programme,we declare variables and compiler allocates memory to them.I want to get access to the physical block number of hard-disk where actually the data is stored by the programme "
Some one help me out... (1 Reply)
Discussion started by: nagraz007
1 Replies
9. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
10. UNIX for Beginners Questions & Answers
Hi.
I have a Microsystems SunBlade 150
shell# cat /etc/release
Solaris 8 2/02 s28s_u7wos_08a SPARC
shell# uname -a
SunOS HOSTNAME 5.8 Generic_108528-14 sun4u sparc SUNW,Sun-Blade-100
shell# prtconf -F
/pci@1f,0/SUNW,m64B@13:m640
When I join to the only account the server try to... (5 Replies)
Discussion started by: siegroup
5 Replies
LEARN ABOUT MINIX
diskscan
diskscan(1M) System Administration Commands diskscan(1M)
NAME
diskscan - perform surface analysis
SYNOPSIS
diskscan [-W] [-n] [-y] raw_device
DESCRIPTION
diskscan is used by the system administrator to perform surface analysis on a portion of a hard disk. The disk portion may be a raw parti-
tion or slice; it is identified using its raw device name. By default, the specified portion of the disk is read (non-destructive) and
errors reported on standard error. In addition, a progress report is printed on standard out. The list of bad blocks should be saved in a
file and later fed into addbadsec(1M), which will remap them.
OPTIONS
The following options are supported:
-n Causes diskscan to suppress linefeeds when printing progress information on standard out.
-W Causes diskscan to perform write and read surface analysis. This type of surface analysis is destructive and should be invoked
with caution.
-y Causes diskscan to suppress the warning regarding destruction of existing data that is issued when -W is used.
OPERANDS
The following operands are supported:
raw_device The address of the disk drive (see FILES).
FILES
The raw device should be /dev/rdsk/c?[t?]d?[ps]?. See disks(1M) for an explanation of SCSI and IDE device naming conventions.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Architecture |x86 |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO
addbadsec(1M), disks(1M), fdisk(1M), fmthard(1M), format(1M), attributes(5)
NOTES
The format(1M) utility is available to format, label, analyze, and repair SCSI disks. This utility is included with the diskscan, addbad-
sec(1M), fdisk(1M), and fmthard(1M) commands available for x86. To format an IDE disk, use the DOS format utility; however, to label, ana-
lyze, or repair IDE disks on x86 systems, use the Solaris format(1M) utility.
SunOS 5.10 24 Feb 1998 diskscan(1M)