Sponsored Content
Top Forums UNIX for Advanced & Expert Users iscsi commands iscsiadm solaris 10 Post 302107432 by sb008 on Friday 16th of February 2007 05:24:03 PM
Old 02-16-2007
svcadm enable iscsi_initiator
 

9 More Discussions You Might Find Interesting

1. Solaris

Solaris 10 10/08 sparc + iSCSI

hi, I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work. Thanks, Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies

2. Solaris

iscsi device on solaris 10 (x64)

Hello! I have several disks discovered using iscsi protocol. There disks are represented in OS like c2txd0 . logs: Is it possible to change drive path, for example, from c2t6d0 to c2t7d0? It's important for me because I have to install oracle RAC on RAW devices. NIck (0 Replies)
Discussion started by: skelet
0 Replies

3. Solaris

Solaris 10 and DELL TL-2000 Tape Library with ISCSI

Hello, i am trying to get following configuration up running, but get no access to the library roboter. Server: SunOS 5.10 Generic_138889-03 i86pc i386 i86pc DELL TL-2000: 1 Tape: IBM ULT3580-HH4 and Robot: 3573-TL, connected via ISCSI Bridge (build into the TL) ... (1 Reply)
Discussion started by: austin73
1 Replies

4. UNIX for Advanced & Expert Users

Solaris 10 10/09 u8, iSCSI and SUN Trunking

I am running Solaris 10 on a V490. I have Dell EqualLogic SAN attached. I would like to take full advantage of the iSCSI initiator. I have a primary network interface and IP addresses for all four SAN ports. Since the four ports are SUN GigaSwift (legacy), I cannot utilize dladm, so I downloaded... (2 Replies)
Discussion started by: KSFlyer
2 Replies

5. Solaris

Set up iscsi LUN on solaris 9?

Hi, I need to set up iscsi LUN on Solaris 9. I've done it on Solaris 10 with iscsiadm. How do you do it on Solaris 9 though? Currently using Solaris 9 update 2. Your help is appreciated. Thanks, Sparcman (6 Replies)
Discussion started by: sparcman
6 Replies

6. UNIX for Dummies Questions & Answers

How to change ethernet cable of iscsi initiator (iscsi client)?

how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies

7. Solaris

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
Discussion started by: ctafret
0 Replies

8. UNIX for Advanced & Expert Users

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies

9. Solaris

Solaris 11 iscsi chap auth

hi to all i've done that steps, but i was not completely successful: sudo pkg install group/feature/storage-server sudo svcadm enable stmf sudo zfs create -V 1g rpool/LUN1 sudo stmfadm create-lu /dev/zvol/rdsk/rpool/LUN1 sudo stmfadm list-lu ... (4 Replies)
Discussion started by: jm83
4 Replies
OCF_HEARTBEAT_ISCSI(7)						OCF resource agents					    OCF_HEARTBEAT_ISCSI(7)

NAME
ocf_heartbeat_iscsi - Manages a local iSCSI initiator and its connections to iSCSI targets SYNOPSIS
iscsi [start | stop | status | monitor | validate-all | methods | meta-data] DESCRIPTION
OCF Resource Agent for iSCSI. Add (start) or remove (stop) iSCSI targets. SUPPORTED PARAMETERS
portal The iSCSI portal address in the form: {ip_address|hostname}[":"port] (required, string, no default) target The iSCSI target IQN. (required, string, no default) discovery_type Target discovery type. Check the open-iscsi documentation for supported discovery types. (optional, string, default sendtargets) iscsiadm open-iscsi administration utility binary. (optional, string, default iscsiadm) udev If the next resource depends on the udev creating a device then we wait until it is finished. On a normally loaded host this should be done quickly, but you may be unlucky. If you are not using udev set this to "no", otherwise we will spin in a loop until a timeout occurs. (optional, string, default yes) SUPPORTED ACTIONS
This resource agent supports the following actions (operations): start Starts the resource. Suggested minimum timeout: 120. stop Stops the resource. Suggested minimum timeout: 120. status Performs a status check. Suggested minimum timeout: 30. monitor Performs a detailed status check. Suggested minimum timeout: 30. Suggested interval: 120. validate-all Performs a validation of the resource configuration. Suggested minimum timeout: 5. methods Suggested minimum timeout: 5. meta-data Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5. EXAMPLE
The following is an example configuration for a iscsi resource using the crm(8) shell: primitive example_iscsi ocf:heartbeat:iscsi params portal=string target=string op monitor depth="0" timeout="30" interval="120" SEE ALSO
http://www.linux-ha.org/wiki/iscsi_(resource_agent) AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors) resource-agents 1.0.3 07/05/2010 OCF_HEARTBEAT_ISCSI(7)
All times are GMT -4. The time now is 08:22 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy