02-16-2007
iscsi commands iscsiadm solaris 10
I'm running solaris 10 and this packages is installed
SUNWiscsir - Sun iSCSI Device Driver (root)
SUNWiscsiu - Sun iSCSI Management Utilities (usr)
But the commands iscsiadm or iscsitadm dont work.
He are not in my system. Do you know the problem.
9 More Discussions You Might Find Interesting
1. Solaris
hi,
I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work.
Thanks,
Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies
2. Solaris
Hello!
I have several disks discovered using iscsi protocol.
There disks are represented in OS like c2txd0 .
logs:
Is it possible to change drive path, for example, from c2t6d0 to c2t7d0?
It's important for me because I have to install oracle RAC on RAW devices.
NIck (0 Replies)
Discussion started by: skelet
0 Replies
3. Solaris
Hello,
i am trying to get following configuration up running, but get no access to the library roboter.
Server: SunOS 5.10 Generic_138889-03 i86pc i386 i86pc
DELL TL-2000: 1 Tape: IBM ULT3580-HH4 and Robot: 3573-TL,
connected via ISCSI Bridge (build into the TL)
... (1 Reply)
Discussion started by: austin73
1 Replies
4. UNIX for Advanced & Expert Users
I am running Solaris 10 on a V490. I have Dell EqualLogic SAN attached.
I would like to take full advantage of the iSCSI initiator.
I have a primary network interface and IP addresses for all four SAN ports. Since the four ports are SUN GigaSwift (legacy), I cannot utilize dladm, so I downloaded... (2 Replies)
Discussion started by: KSFlyer
2 Replies
5. Solaris
Hi,
I need to set up iscsi LUN on Solaris 9. I've done it on Solaris 10 with iscsiadm. How do you do it on Solaris 9 though? Currently using Solaris 9 update 2. Your help is appreciated.
Thanks,
Sparcman (6 Replies)
Discussion started by: sparcman
6 Replies
6. UNIX for Dummies Questions & Answers
how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies
7. Solaris
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
Discussion started by: ctafret
0 Replies
8. UNIX for Advanced & Expert Users
I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got
fdisk: "Error in ioctl DKIOCSMBOOT"
Details --
According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies
9. Solaris
hi to all
i've done that steps, but i was not completely successful:
sudo pkg install group/feature/storage-server
sudo svcadm enable stmf
sudo zfs create -V 1g rpool/LUN1
sudo stmfadm create-lu /dev/zvol/rdsk/rpool/LUN1
sudo stmfadm list-lu ... (4 Replies)
Discussion started by: jm83
4 Replies
LEARN ABOUT CENTOS
iscsistart
ISCSISTART(8) Linux Administrator's Manual ISCSISTART(8)
NAME
iscsistart - iSCSI boot tool
SYNOPSIS
iscsistart [OPTION]
DESCRIPTION
iscsistart will start a session using the settings passed in, or using the iBFT or Open Firmware [OF] boot information. This program should
not be run to manage sessions. Its primary use is to start sessions used for iSCSI root boot.
OPTIONS
[-i|--initiatorname=]name
Set InitiatorName to name (Required if not using iBFT or OF)
[-t|--targetname=]name
Set TargetName to name (Required if not using iBFT or OF)
[-g|--tgpt=]N
Set target portal group tag to N (Required if not using iBFT or OF)
[-a|--address=]A.B.C.D
Set IP addres to A.B.C.D (Required if not using iBFT or OF)
[-p|--port=]N
Set port to N (Optional. Default 3260)
[-u|--username=]N
Set username to N (Optional)
[-w|--password=]N
Set password to N (Optional)
[-U|-username_in=]N
Set incoming username to N (Optional)
[-W|--password_in=]N
Set incoming password to N (Optional)
[-d|--debug=]debug_level
Print debugging information
[-b|--fwparam_connect]
Create a session to the target using the iBFT or OF info
[-N|--fwparam_network]
Bring up the network as specified by iBFT or OF
[-f|--fwparam_print]
Print the iBFT or OF info to STDOUT
[-P|--param=]NAME=VALUE
Set the parameter with the name NAME to VALUE. NAME is one of the settings in the node record or iscsid.conf. Multiple params can be
passed in.
[-h|--help]
Display this help and exit
[-v|--version]
Display version and exit
SEE ALSO
iscsiadm(8)
AUTHORS
Open-iSCSI project <http://www.open-iscsi.org/>
Mike Christie <mchristi@redhat.com>
Jan 2010 ISCSISTART(8)