Sponsored Content
Top Forums UNIX for Advanced & Expert Users iscsi commands iscsiadm solaris 10 Post 302107424 by simonquest on Friday 16th of February 2007 03:52:45 PM
Old 02-16-2007
iscsi commands iscsiadm solaris 10

I'm running solaris 10 and this packages is installed

SUNWiscsir - Sun iSCSI Device Driver (root)
SUNWiscsiu - Sun iSCSI Management Utilities (usr)

But the commands iscsiadm or iscsitadm dont work.
He are not in my system. Do you know the problem.
 

9 More Discussions You Might Find Interesting

1. Solaris

Solaris 10 10/08 sparc + iSCSI

hi, I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work. Thanks, Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies

2. Solaris

iscsi device on solaris 10 (x64)

Hello! I have several disks discovered using iscsi protocol. There disks are represented in OS like c2txd0 . logs: Is it possible to change drive path, for example, from c2t6d0 to c2t7d0? It's important for me because I have to install oracle RAC on RAW devices. NIck (0 Replies)
Discussion started by: skelet
0 Replies

3. Solaris

Solaris 10 and DELL TL-2000 Tape Library with ISCSI

Hello, i am trying to get following configuration up running, but get no access to the library roboter. Server: SunOS 5.10 Generic_138889-03 i86pc i386 i86pc DELL TL-2000: 1 Tape: IBM ULT3580-HH4 and Robot: 3573-TL, connected via ISCSI Bridge (build into the TL) ... (1 Reply)
Discussion started by: austin73
1 Replies

4. UNIX for Advanced & Expert Users

Solaris 10 10/09 u8, iSCSI and SUN Trunking

I am running Solaris 10 on a V490. I have Dell EqualLogic SAN attached. I would like to take full advantage of the iSCSI initiator. I have a primary network interface and IP addresses for all four SAN ports. Since the four ports are SUN GigaSwift (legacy), I cannot utilize dladm, so I downloaded... (2 Replies)
Discussion started by: KSFlyer
2 Replies

5. Solaris

Set up iscsi LUN on solaris 9?

Hi, I need to set up iscsi LUN on Solaris 9. I've done it on Solaris 10 with iscsiadm. How do you do it on Solaris 9 though? Currently using Solaris 9 update 2. Your help is appreciated. Thanks, Sparcman (6 Replies)
Discussion started by: sparcman
6 Replies

6. UNIX for Dummies Questions & Answers

How to change ethernet cable of iscsi initiator (iscsi client)?

how to change ethernet cable of iscsi initiator (iscsi client) (0 Replies)
Discussion started by: pankajd
0 Replies

7. Solaris

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
Discussion started by: ctafret
0 Replies

8. UNIX for Advanced & Expert Users

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (1 Reply)
Discussion started by: ctafret
1 Replies

9. Solaris

Solaris 11 iscsi chap auth

hi to all i've done that steps, but i was not completely successful: sudo pkg install group/feature/storage-server sudo svcadm enable stmf sudo zfs create -V 1g rpool/LUN1 sudo stmfadm create-lu /dev/zvol/rdsk/rpool/LUN1 sudo stmfadm list-lu ... (4 Replies)
Discussion started by: jm83
4 Replies
ISCSI(4)						   BSD Kernel Interfaces Manual 						  ISCSI(4)

NAME
iscsi -- iSCSI initiator SYNOPSIS
To compile this driver into the kernel, place the following line in the kernel configuration file: device iscsi Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): iscsi_load="YES" DESCRIPTION
The iscsi subsystem provides the kernel component of an iSCSI initiator. The initiator is the iSCSI client, which connects to an iSCSI tar- get, providing local access to a remote block device. The userland component is provided by iscsid(8) and both the kernel and userland are configured using iscsictl(8). The iscsi subsystem is responsible for implementing the "Full Feature Phase" of the iSCSI protocol. SYSCTL VARIABLES
The following variables are available as both sysctl(8) variables and loader(8) tunables: kern.iscsi.ping_timeout The number of seconds to wait for the target to respond to a NOP-Out PDU. In the event that there is no response within that time the session gets forcibly restarted. kern.iscsi.iscsid_timeout The number of seconds to wait for ctld(8) to establish a session. After that time iscsi will abort and retry. kern.iscsi.login_timeout The number of seconds to wait for a login attempt to succeed. After that time iscsi will abort and retry. kern.iscsi.maxtags The maximum number of outstanding IO requests. kern.iscsi.fail_on_disconnection Controls the behavior after an iSCSI connection has been dropped due to network problems. When set to 1, a dropped connection causes the iSCSI device nodes to be destroyed. After reconnecting, they will be created again. By default, the device nodes are left intact. While the connection is down all input/output operations are suspended, to be retried after the connection is reestablished. SEE ALSO
iscsi.conf(5), iscsictl(8), iscsid(8) HISTORY
The iscsi subsystem first appeared in FreeBSD 10.0. AUTHORS
The iscsi subsystem was developed by Edward Tomasz Napierala <trasz@FreeBSD.org> under sponsorship from the FreeBSD Foundation. BSD
September 11, 2014 BSD
All times are GMT -4. The time now is 04:33 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy