02-16-2007
In some way, I think you haven't explain so well how your network architecture is,.. thus it is difficult that someone can help you
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can i set an permanent route so that itīs still here after a reboot ?
i have a gateways file
Thanks
:confused: :confused: :confused: (1 Reply)
Discussion started by: redcrosskbg
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Discussion started by: nhatch
3 Replies
3. IP Networking
Is ther a way to retain say, a default gateway entered in a routing table after a reboot? I end up always having to re-enter my default gateway after I reboot my system.
Thanks! (4 Replies)
Discussion started by: thundrrod
4 Replies
4. IP Networking
hi all,
how to access ip routing table throgh program,
how should i integrate my rip routing table with the ip routing table :) (0 Replies)
Discussion started by: vinodkumar
0 Replies
5. AIX
i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service.
thanks (1 Reply)
Discussion started by: jdsnbr
1 Replies
6. IP Networking
hi all...
i need to know, where is locate the routing table on sun solaris, how i can saved the configuration....
because when i restart the server, lost the configuration....
thank you...
Regards... (3 Replies)
Discussion started by: chanfle
3 Replies
7. Linux
Hello,
how to make entries in routing table perminent (1 Reply)
Discussion started by: teenasuresh
1 Replies
8. Red Hat
I have below routing table in linux kernel 2.6.9
# netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.155.24.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U ... (5 Replies)
Discussion started by: chuikingman
5 Replies
9. IP Networking
Hello.
Is there any way to restore back the default ip routing table ?
For example, my current routing table is something like
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
109.123.95.0 0.0.0.0 255.255.255.0 U 0 ... (0 Replies)
Discussion started by: anid
0 Replies
10. HP-UX
Hi all,
Could someone please explain to me how I should read this routing table,
# netstat -rn
Routing tables
Destination Gateway Flags Refs Interface Pmtu
127.0.0.1 127.0.0.1 UH 0 lo0 32808
10.222.47.82 10.222.47.82 UH... (3 Replies)
Discussion started by: rachael
3 Replies
LEARN ABOUT CENTOS
struct_kgdb_arch
STRUCT
KGDB_ARCH(9) Kernel Debugger Internals STRUCT KGDB_ARCH(9)
NAME
struct_kgdb_arch - Describe architecture specific values.
SYNOPSIS
struct kgdb_arch {
unsigned char gdb_bpt_instr[BREAK_INSTR_SIZE];
unsigned long flags;
int (* set_breakpoint) (unsigned long, char *);
int (* remove_breakpoint) (unsigned long, char *);
int (* set_hw_breakpoint) (unsigned long, int, enum kgdb_bptype);
int (* remove_hw_breakpoint) (unsigned long, int, enum kgdb_bptype);
void (* disable_hw_break) (struct pt_regs *regs);
void (* remove_all_hw_break) (void);
void (* correct_hw_break) (void);
void (* enable_nmi) (bool on);
};
MEMBERS
gdb_bpt_instr[BREAK_INSTR_SIZE]
The instruction to trigger a breakpoint.
flags
Flags for the breakpoint, currently just KGDB_HW_BREAKPOINT.
set_breakpoint
Allow an architecture to specify how to set a software breakpoint.
remove_breakpoint
Allow an architecture to specify how to remove a software breakpoint.
set_hw_breakpoint
Allow an architecture to specify how to set a hardware breakpoint.
remove_hw_breakpoint
Allow an architecture to specify how to remove a hardware breakpoint.
disable_hw_break
Allow an architecture to specify how to disable hardware breakpoints for a single cpu.
remove_all_hw_break
Allow an architecture to specify how to remove all hardware breakpoints.
correct_hw_break
Allow an architecture to specify how to correct the hardware debug registers.
enable_nmi
Manage NMI-triggered entry to KGDB
AUTHOR
Jason Wessel <jason.wessel@windriver.com>
Author.
COPYRIGHT
Kernel Hackers Manual 3.10 June 2014 STRUCT KGDB_ARCH(9)