02-16-2007
In some way, I think you haven't explain so well how your network architecture is,.. thus it is difficult that someone can help you
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How can i set an permanent route so that itīs still here after a reboot ?
i have a gateways file
Thanks
:confused: :confused: :confused: (1 Reply)
Discussion started by: redcrosskbg
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I'm trying to connect to a network device, with the connection follwoing the UNIX routing table we set up. Its to go via a specific network Gateway and out throught a specific Lan card (Lan4). However when trying to conenct it keeps going through Lan3 and will not get to its destination.... (3 Replies)
Discussion started by: nhatch
3 Replies
3. IP Networking
Is ther a way to retain say, a default gateway entered in a routing table after a reboot? I end up always having to re-enter my default gateway after I reboot my system.
Thanks! (4 Replies)
Discussion started by: thundrrod
4 Replies
4. IP Networking
hi all,
how to access ip routing table throgh program,
how should i integrate my rip routing table with the ip routing table :) (0 Replies)
Discussion started by: vinodkumar
0 Replies
5. AIX
i have AIX Unix with "dynamic routing table" service enabled, but i do not need this service. How i can disable this service.
thanks (1 Reply)
Discussion started by: jdsnbr
1 Replies
6. IP Networking
hi all...
i need to know, where is locate the routing table on sun solaris, how i can saved the configuration....
because when i restart the server, lost the configuration....
thank you...
Regards... (3 Replies)
Discussion started by: chanfle
3 Replies
7. Linux
Hello,
how to make entries in routing table perminent (1 Reply)
Discussion started by: teenasuresh
1 Replies
8. Red Hat
I have below routing table in linux kernel 2.6.9
# netstat -rn
Kernel IP routing table
Destination Gateway Genmask Flags MSS Window irtt Iface
10.155.24.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0
169.254.0.0 0.0.0.0 255.255.0.0 U ... (5 Replies)
Discussion started by: chuikingman
5 Replies
9. IP Networking
Hello.
Is there any way to restore back the default ip routing table ?
For example, my current routing table is something like
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
109.123.95.0 0.0.0.0 255.255.255.0 U 0 ... (0 Replies)
Discussion started by: anid
0 Replies
10. HP-UX
Hi all,
Could someone please explain to me how I should read this routing table,
# netstat -rn
Routing tables
Destination Gateway Flags Refs Interface Pmtu
127.0.0.1 127.0.0.1 UH 0 lo0 32808
10.222.47.82 10.222.47.82 UH... (3 Replies)
Discussion started by: rachael
3 Replies
LEARN ABOUT DEBIAN
vlan-interfaces
VLAN-INTERFACES(5) File formats VLAN-INTERFACES(5)
NAME
/etc/network/interfaces (vlan) - vlan extensions for the interfaces(5) file format
DESCRIPTION
/etc/network/interfaces contains network interface configuration information for the ifup(8) and ifdown(8) commands. This manpage
describes the vlan extensions to the standard interfaces(5) file format.
Primary extensions exist to make and destroy vlan interfaces, secondary extensions exist for ipv4 interface manipulation which are gener-
ally needed when using (a lot of) vlans.
VLAN CREATION
Vlan interface definitions exist of the vlan interface name, and an optional 'raw-device' parameter. Vlan interfaces are numbered 1 to
4095. You have the option to have interface names zero-padded to 4 numbers, or just the plain digits without leading zero. The following
example shows four ways to create a vlan with id 1 on interface eth0. They all result in different names.
iface eth0.1 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan1 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
iface eth0.0001 inet static
address 192.168.1.1
netmask 255.255.255.0
iface vlan0001 inet static
vlan-raw-device eth0
address 192.168.1.1
netmask 255.255.255.0
# We don't have br support out of the box
iface br0.2 inet static
vlan-raw-device br0
address 192.168.1.1
netmask 255.255.255.0
# Aliases are ignored
iface br0.2:1 inet static
address 192.168.1.1
netmask 255.255.255.255
EXTRA IFACE OPTIONS
Usually someone who uses vlans also wants to do some other manipulations with the ip stack or interface.
vlan-raw-device devicename
Indicates the device to create the vlan on. This is ignored when the devicename is part of the vlan interface name.
ip-proxy-arp 0|1
Turn proxy-arp off or on for this specific interface. This also works on plain ethernet like devices.
ip-rp-filter 0|1|2
Set the return path filter for this specific interface. This also works on plain ethernet like devices.
hw-mac-address mac-address
This sets the mac address of the interface before bringing it up. This works on any device that allows setting the hardware address
with the ip command.
AUTHOR
This manpage was adapted from interfaces(5) by Ard van Breemen <ard@kwaak.net>
SEE ALSO
vconfig(8) interfaces(5)
vlan September 30 2007 VLAN-INTERFACES(5)