01-22-2007
Kill several processes at a time
Hello,
ps -C a*
returns the list of the process I need to kill.
but
ps -C a* -o pid | kill
does not work and I can't get the syntax right.
Thanks for any help
10 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
i have a very short file that has in it a line for a find command.
now, when i run this script and I kill the script later, using the ps -ef | grep scriptname. i noticed kill -9 kills the script itself but does not kill the internal find command that it gave birth to.
say theres a file... (0 Replies)
Discussion started by: Terrible
0 Replies
2. Shell Programming and Scripting
Hi guys,
I am new to Unix shell scripting. Can anyone of you tell me how to kill all the processes at a time for a particular user?(No listing the process ID of each process in the kill -9 command).
Thanks in Advance,
-Hary (5 Replies)
Discussion started by: tadi18
5 Replies
3. Solaris
mqm 17700 16815 0 0:00 <defunct>
kill -9 does not work, even as root (10 Replies)
Discussion started by: csaunders
10 Replies
4. Solaris
how to kill the processes of aperticular user?
because i have nearly 25000 process are there for perticular user. i need to kill.
Please provide the information?
Regards,
Rajesh (3 Replies)
Discussion started by: pmrajesh21
3 Replies
5. HP-UX
Hi,
I read a set of processes with:
ps -eaf|grep oracleTRLV
The result is:
oracle 23253 1 0 15:14:11 ? 0:00 oracleTRLV (LOCAL=NO)
oracle 23301 1 0 15:15:07 ? 0:00 oracleTRLV (LOCAL=NO)
oracle 22914 1 0 15:11:19 ? 0:00 oracleTRLV (LOCAL=NO)
How to I kill the "oracleTRLV" ones? Is there... (17 Replies)
Discussion started by: NicoMan
17 Replies
6. Solaris
Hi,
How to kill the processes running under ptree ?
I am noticing lot of processes running under ptree with ssh ? I tried to kill with -9 option which is not working ?
Thanks,
Radhika. (2 Replies)
Discussion started by: radhirk
2 Replies
7. Shell Programming and Scripting
for i in 'ps -f | grep textedit'
do
kill $i
done
I wrote this but it wont work.
I am trying to find processes and kill them.
Any help would be welcome. (1 Reply)
Discussion started by: hawaiifiver
1 Replies
8. Shell Programming and Scripting
Hi,
when i grep for the process "XYZ" , there will be some good number of processes with that name, i want to kill all the these processes at a time using shell script?
Any help needed for this action.
Thanks
Regards,
Anil (6 Replies)
Discussion started by: anilmanepu
6 Replies
9. Shell Programming and Scripting
Want to kill multiple processes by name. for the example below, I want to kill all 'proxy-stagerd_copy' processes.
I tried this but didn't work:
>> ps -ef|grep proxy_copy
root 991 986 0 14:45:34 ? 0:04 proxy-stagerd
root 1003 991 0 14:45:49 ? 0:01... (2 Replies)
Discussion started by: catalinawinemxr
2 Replies
10. UNIX for Advanced & Expert Users
I am trying to kill a list of processes. I have found these two ways to list a group of process id's on a single line. How would I go about killing all of these processes all on one line?
$ ps aux | grep 6243 | grep "a.out" | awk '{printf "%s ",$2}'ps aux | grep 6243 | grep "a.out" | awk... (8 Replies)
Discussion started by: cokedude
8 Replies
KILL(1) BSD General Commands Manual KILL(1)
NAME
kill -- terminate or signal a process
SYNOPSIS
kill [-s signal_name] pid ...
kill -l [exit_status]
kill -signal_name pid ...
kill -signal_number pid ...
DESCRIPTION
The kill utility sends a signal to the processes specified by the pid operand(s).
Only the super-user may send signals to other users' processes.
The options are as follows:
-s signal_name
A symbolic signal name specifying the signal to be sent instead of the default TERM.
-l [exit_status]
If no operand is given, list the signal names; otherwise, write the signal name corresponding to exit_status.
-signal_name
A symbolic signal name specifying the signal to be sent instead of the default TERM.
-signal_number
A non-negative decimal integer, specifying the signal to be sent instead of the default TERM.
The following pids have special meanings:
-1 If superuser, broadcast the signal to all processes; otherwise broadcast to all processes belonging to the user.
Some of the more commonly used signals:
1 HUP (hang up)
2 INT (interrupt)
3 QUIT (quit)
6 ABRT (abort)
9 KILL (non-catchable, non-ignorable kill)
14 ALRM (alarm clock)
15 TERM (software termination signal)
Some shells may provide a builtin kill command which is similar or identical to this utility. Consult the builtin(1) manual page.
SEE ALSO
builtin(1), csh(1), killall(1), ps(1), kill(2), sigaction(2)
STANDARDS
The kill function is expected to be IEEE Std 1003.2 (``POSIX.2'') compatible.
HISTORY
A kill command appeared in Version 6 AT&T UNIX.
BUGS
A replacement for the command ``kill 0'' for csh(1) users should be provided.
BSD
April 28, 1995 BSD