IDE DISK ERR2 and LVM SA STALEPP errors in errpt Post: 302102249

9 More Discussions You Might Find Interesting

1. AIX

AIX 5.3 errpt full of message: DISK OPERATION ERROR

Hi All, Can anyone explain me the meanning of the following errors: LABEL: SC_DISK_ERR2 IDENTIFIER: B6267342 Description DISK OPERATION ERROR Probable Causes DASD DEVICE Failure Causes DISK DRIVE DISK DRIVE ELECTRONICS Recommended Actions PERFORM PROBLEM DETERMINATION...

2. Filesystems, Disks and Memory

shift hard disk from primary IDE channel to secondary IDE channal

Wellcomes All, some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE...

3. Solaris

problem after adding new ide disk

Hi experts, i have added a new disk to my ultra 10 system, after that i am unable to boot the system, its not booting from disk neither from cd. please help! Regards

4. Filesystems, Disks and Memory

Wrong BIOS IDE Settings on a SATA disk (AHCI)?

Hello, I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future. Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The...

5. UNIX Desktop Questions & Answers

Maximize IDE Hard Disk

Hi there! I am installing Unixware 7.1 to a new server. We usually use SCSI hard for this but since this will be used only for testing, I decided to use an 80GB IDE hard disk. I was able to successfully load the unix but found out that the 80GB hard disk was not maximized. The total hard disk...

6. AIX

Disk I/O Issue using LVM

We have a filesystem which contains 8 hard disks but i am facing disk I/O issue becuase data is not spreading across all the disks.Is there any way i can check how data is spreading and any parameter we need to change to spread ata across all disks. OS--AIX 5.3

7. SCO

declare disk driver for IDE hard disk

hi I've a fresh installation of SCO 5.0.7 on the IDE hard disk. For SCSI hard disk I can declare, for example blc disk driver using: # mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk?

8. AIX

How to read or understand errors in errpt

Hello, after upgrading the memory to 96GB & 6 Dual Processor for P 550 ( and still not applied the parameters which some experienced posters said in post https://www.unix.com/aix/141835-oracle-database-running-slow-aix-nmon-topas-6.html ) I am getting system dumps. How to understand and...

9. AIX

errpt kept sending errors after disk replacement

Hi, The system is a Power6 8204 with an external storage 7031. OS is AIX 5.3. I replaced a failed disk hdisk28 and put it back to the volume group. Everything looks just fine. After the replacement, errpt has kept sending "Perm DISK OPERATION ERROR". Other than the error, everything still...

LEARN ABOUT MOJAVE

gldeletesync

GLDELETESYNC(3G)						    OpenGL 3.3							  GLDELETESYNC(3G)

NAME

       glDeleteSync - delete a sync object

C SPECIFICATION

       void glDeleteSync(GLsync sync);

PARAMETERS

       sync
	   The sync object to be deleted.

DESCRIPTION

       glDeleteSync deletes the sync object specified by sync. If the fence command corresponding to the specified sync object has completed, or
       if no glWaitSync() or glClientWaitSync() commands are blocking on sync, the object is deleted immediately. Otherwise, sync is flagged for
       deletion and will be deleted when it is no longer associated with any fence command and is no longer blocking any glWaitSync() or
       glClientWaitSync() command. In either case, after glDeleteSync returns, the name sync is invalid and can no longer be used to refer to the
       sync object.

       glDeleteSync will silently ignore a sync value of zero.

NOTES

       glSync is only supported if the GL version is 3.2 or greater, or if the ARB_sync extension is supported.

ERRORS

       GL_INVALID_VALUE is generated if sync is neither zero or the name of a sync object.

SEE ALSO

       glFenceSync(), glWaitSync(), glClientWaitSync()

COPYRIGHT

       Copyright (C) 2010 Khronos Group. This material may be distributed subject to the terms and conditions set forth in the Open Publication
       License, v 1.0, 8 June 1999.  http://opencontent.org/openpub/.

OpenGL 3.3							    03/08/2011							  GLDELETESYNC(3G)