Sponsored Content
Operating Systems AIX IDE DISK ERR2 and LVM SA STALEPP errors in errpt Post 302102177 by johnf on Tuesday 9th of January 2007 01:54:14 AM
Old 01-09-2007
Any disk device errors in the error log? Sounds to me like a hard disk failing.
 

9 More Discussions You Might Find Interesting

1. AIX

AIX 5.3 errpt full of message: DISK OPERATION ERROR

Hi All, Can anyone explain me the meanning of the following errors: LABEL: SC_DISK_ERR2 IDENTIFIER: B6267342 Description DISK OPERATION ERROR Probable Causes DASD DEVICE Failure Causes DISK DRIVE DISK DRIVE ELECTRONICS Recommended Actions PERFORM PROBLEM DETERMINATION... (1 Reply)
Discussion started by: gianlu
1 Replies

2. Filesystems, Disks and Memory

shift hard disk from primary IDE channel to secondary IDE channal

Wellcomes All, some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
Discussion started by: thekarsillo
1 Replies

3. Solaris

problem after adding new ide disk

Hi experts, i have added a new disk to my ultra 10 system, after that i am unable to boot the system, its not booting from disk neither from cd. please help! Regards (16 Replies)
Discussion started by: kumarmani
16 Replies

4. Filesystems, Disks and Memory

Wrong BIOS IDE Settings on a SATA disk (AHCI)?

Hello, I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future. Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
Discussion started by: septima.pars
0 Replies

5. UNIX Desktop Questions & Answers

Maximize IDE Hard Disk

Hi there! I am installing Unixware 7.1 to a new server. We usually use SCSI hard for this but since this will be used only for testing, I decided to use an 80GB IDE hard disk. I was able to successfully load the unix but found out that the 80GB hard disk was not maximized. The total hard disk... (1 Reply)
Discussion started by: limpinmd
1 Replies

6. AIX

Disk I/O Issue using LVM

We have a filesystem which contains 8 hard disks but i am facing disk I/O issue becuase data is not spreading across all the disks.Is there any way i can check how data is spreading and any parameter we need to change to spread ata across all disks. OS--AIX 5.3 (1 Reply)
Discussion started by: ukatru
1 Replies

7. SCO

declare disk driver for IDE hard disk

hi I've a fresh installation of SCO 5.0.7 on the IDE hard disk. For SCSI hard disk I can declare, for example blc disk driver using: # mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Discussion started by: ccc
3 Replies

8. AIX

How to read or understand errors in errpt

Hello, after upgrading the memory to 96GB & 6 Dual Processor for P 550 ( and still not applied the parameters which some experienced posters said in post https://www.unix.com/aix/141835-oracle-database-running-slow-aix-nmon-topas-6.html ) I am getting system dumps. How to understand and... (1 Reply)
Discussion started by: filosophizer
1 Replies

9. AIX

errpt kept sending errors after disk replacement

Hi, The system is a Power6 8204 with an external storage 7031. OS is AIX 5.3. I replaced a failed disk hdisk28 and put it back to the volume group. Everything looks just fine. After the replacement, errpt has kept sending "Perm DISK OPERATION ERROR". Other than the error, everything still... (1 Reply)
Discussion started by: aixlover
1 Replies
hdio(7I)							  Ioctl Requests							  hdio(7I)

NAME
hdio - SMD and IPI disk control operations SYNOPSIS
#include <sys/hdio.h> DESCRIPTION
Note - The SMC and IPI drivers have been discontinued. dkio(7I) is now the preferred method for retrieving disk information. The SMD and IPI disk drivers supplied with this release support a set of ioctl(2) requests for diagnostics and bad sector information. Basic to these ioctl() requests are the definitions in <sys/hdio.h>. IOCTLS
HDKIOCGTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() gets specific information from the hard disk. HDKIOCSTYPE The argument is a pointer to a hdk_type structure (described below). This ioctl() sets specific information about the hard disk. /* * Used for drive info */ struct hdk_type { ushort_t hdkt_hsect; /* hard sector count (read only) */ ushort_t hdkt_promrev; /* prom revision (read only) */ uchar_t hdkt_drtype; /* drive type (ctlr specific) */ uchar_t hdkt_drstat; /* drive status (ctlr specific, ro) */ }; HDKIOCGBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to get the bad sector map from the disk. HDKIOCSBAD The argument is a pointer to a hdk_badmap structure (described below). This ioctl() is used to set the bad sector map on the disk. /* * Used for bad sector map */ struct hdk_badmap { caddr_t hdkb_bufaddr; /* address of user's map buffer */ }; HDKIOCGDIAG The argument is a pointer to a hdk_diag structure (described below). This ioctl() gets the most recent command that failed along with the sector and error number from the hard disk. /* * Used for disk diagnostics */ struct hdk_diag { ushort_t hdkd_errcmd; /* most recent command in error */ daddr_t hdkd_errsect; /* most recent sector in error */ uchar_t hdkd_errno; /* most recent error number */ uchar_t hdkd_severe; /* severity of most recent error */ }; SEE ALSO
ioctl(2), dkio(7I) SunOS 5.10 13 Aug 2002 hdio(7I)
All times are GMT -4. The time now is 09:58 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy