Sponsored Content
Full Discussion: unable to ping
Top Forums UNIX for Dummies Questions & Answers unable to ping Post 302101496 by jimmyc on Tuesday 2nd of January 2007 08:06:21 AM
Old 01-02-2007
Off hand I'd say you have a driver problem. Look for an update or the one needs with what ever it is your running....

Last edited by jimmyc; 01-02-2007 at 01:43 PM..
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Unable to ping host

Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: - 1 QNX host->Eth->1 SCO host the SCO host is configured with it's IP the QNX host is configured with another IP both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies

2. UNIX for Dummies Questions & Answers

unable ping ipaddress

I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the etc/tcp etc/hosts files which i did. still unable to ping. i am getting a message unable to route to host. I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies

3. UNIX for Dummies Questions & Answers

UNable to find ping command

HI, I am new to unix. I have used some basic commands and written some simple shell scripts in teh past. Currently, I am supposed to write a script to continuosly check if a couple of machines are up and if not to start a script. I am using a bash - 2.03. I have tryying to use the ping command... (3 Replies)
Discussion started by: swepaul
3 Replies

4. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies

5. Solaris

unable to ping server

hi, I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise? Test that i have done: -My client pc cannot ping the server. -My solaris server cannot ping client -My solaris server can ping it's gateway -Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies

6. IP Networking

unable to ping to my server

hi, I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise? Test that i have done: -My client pc cannot ping the server. -My solaris server cannot ping client -My solaris server can ping it's gateway -Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies

7. Solaris

Unable to ping New server

Hi ALL, I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network bk (1 Reply)
Discussion started by: suresh_krish
1 Replies

8. Solaris

Unable to ping Windows

Hello, Am unable to ping the Windows Box, from my Solaris Box. They both are in same LAN, have the same IP Segments. Windows IP :: 10.141.14.120 Solaris IP :: 10.141.14.11 Unable to get why isnt working out.... When using the command 'ping 10.141.14.120', it gives the error as 'ping:... (4 Replies)
Discussion started by: jayanto
4 Replies

9. AIX

Unable to ping localhost

Hi all, I have gone through many posts related to this issue,but my issue wasn't resolved hence creating new thread. I am unable to ping localhost. ping localhost tries to ping localhost which is defined in DNS. My /etc/hosts has entry for localhost as 127.0.0.1 loopback localhost. ... (8 Replies)
Discussion started by: chpsam
8 Replies

10. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
3C589_CS(4)						     Kernel Interfaces Manual						       3C589_CS(4)

NAME
3c589_cs - 3Com 3c589 Etherlink III device driver SYNOPSIS
insmod 3c589_cs.o [pc_debug=n] [if_port=n] [irq_list=i,j,...] DESCRIPTION
3c589_cs is the low-level Card Services driver for the 3Com 3c589 PCMCIA ethernet adapter and 3Com 3c562/3c563 combo cards. When this driver is attached to a card, it allocates the next available ethernet device (eth0..eth#). This device name will be reported in the ker- nel log file, and passed on to cardmgr(8). With the default transceiver setting, the driver will attempt to continuously autodetect the transceiver type (10base2 or 10baseT). There should normally only be a one or two second lag before the correct transceiver is selected. On particularly noisy or busy networks, it is possible for the detection logic to incorrectly toggle the transceiver type. If this becomes a problem, it may be necessary to explicitly select the interface type when the module is loaded or with the ifport command. PARAMETERS
pc_debug=n Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero value enables debugging. if_port=n Selects the transceiver type. 0 is autodetect (10baseT or 10base2), 1 is 10baseT (twisted pair), 2 is 10base2 (BNC, or thin net). and 3 is AUI (thick ethernet). The default is 0 (autodetect). irq_list=i,j,... Specifies the set of interrupts that may be allocated by this driver. DIAGNOSTICS
eth#: interrupt(s) dropped! Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi- cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration problem. AUTHOR
David Hinds - dahinds@users.sourceforge.net SEE ALSO
cardmgr(8), pcmcia(5), ifport(8). pcmcia-cs 2000/06/12 21:24:48 3C589_CS(4)
All times are GMT -4. The time now is 09:44 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy