01-02-2007
Off hand I'd say you have a driver problem. Look for an update or the one needs with what ever it is your running....
Last edited by jimmyc; 01-02-2007 at 01:43 PM..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi, dear all, I am rather new to Unix and have this problem where I cant seem to ping from 1 host to another. The scenerio is as follows: -
1 QNX host->Eth->1 SCO host
the SCO host is configured with it's IP
the QNX host is configured with another IP
both in the same domain, ie, 172.20.3.XX... (3 Replies)
Discussion started by: gavon
3 Replies
2. UNIX for Dummies Questions & Answers
I have Sco openserver 5.0. It had a 125. ip. I changed it to a 192. ip. was unable to ping the 192. I was told to change it in the
etc/tcp
etc/hosts
files which i did. still unable to ping.
i am getting a message unable to route to host.
I also have an error in my etc/tcp file on line... (1 Reply)
Discussion started by: pdoug76
1 Replies
3. UNIX for Dummies Questions & Answers
HI,
I am new to unix. I have used some basic commands and written some simple shell scripts in teh past. Currently, I am supposed to write a script to continuosly check if a couple of machines are up and if not to start a script. I am using a bash - 2.03. I have tryying to use the ping command... (3 Replies)
Discussion started by: swepaul
3 Replies
4. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
5. Solaris
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the server... (2 Replies)
Discussion started by: skiturn
2 Replies
6. IP Networking
hi,
I setup a Solaris machine in my server room and my client cannot access it. Can anyone advise?
Test that i have done:
-My client pc cannot ping the server.
-My solaris server cannot ping client
-My solaris server can ping it's gateway
-Another NT machine 1 (10.179.30.26) in the... (8 Replies)
Discussion started by: skiturn
8 Replies
7. Solaris
Hi ALL,
I Have installed NEW v240 server through hyper terminal, After installation i unable to ping the server from out side server... i can see no entry in resolve.conf file.. but the server has DNS.. willl that issue.. please guide me ping the server from outside within the same network
bk (1 Reply)
Discussion started by: suresh_krish
1 Replies
8. Solaris
Hello,
Am unable to ping the Windows Box, from my Solaris Box.
They both are in same LAN, have the same IP Segments.
Windows IP :: 10.141.14.120
Solaris IP :: 10.141.14.11
Unable to get why isnt working out.... When using the command 'ping 10.141.14.120', it gives the error as 'ping:... (4 Replies)
Discussion started by: jayanto
4 Replies
9. AIX
Hi all,
I have gone through many posts related to this issue,but my issue wasn't resolved hence creating new thread.
I am unable to ping localhost.
ping localhost tries to ping localhost which is defined in DNS.
My /etc/hosts has entry for localhost as
127.0.0.1 loopback localhost.
... (8 Replies)
Discussion started by: chpsam
8 Replies
10. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
LEARN ABOUT REDHAT
update
update(n) Tcl Built-In Commands update(n)
__________________________________________________________________________________________________________________________________________________
NAME
update - Process pending events and idle callbacks
SYNOPSIS
update ?idletasks?
_________________________________________________________________
DESCRIPTION
This command is used to bring the application ``up to date'' by entering the event loop repeatedly until all pending events (including idle
callbacks) have been processed.
If the idletasks keyword is specified as an argument to the command, then no new events or errors are processed; only idle callbacks are
invoked. This causes operations that are normally deferred, such as display updates and window layout calculations, to be performed imme-
diately.
The update idletasks command is useful in scripts where changes have been made to the application's state and you want those changes to
appear on the display immediately, rather than waiting for the script to complete. Most display updates are performed as idle callbacks,
so update idletasks will cause them to run. However, there are some kinds of updates that only happen in response to events, such as those
triggered by window size changes; these updates will not occur in update idletasks.
The update command with no options is useful in scripts where you are performing a long-running computation but you still want the applica-
tion to respond to events such as user interactions; if you occasionally call update then user input will be processed during the next
call to update.
SEE ALSO
after(n), bgerror(n)
KEYWORDS
event, flush, handler, idle, update
Tcl 7.5 update(n)