Can mailx use a specified interface? Post: 302100410

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

mailx error message : mailx: NUL changed to @

If I use the "Mail" link instead of the "mail" link to ../mailx I get this error. Mail so-n-so @whatever.com mailx: NUL changed to @ Unknown command: "postmaster" The email still goes through but i get the error. If I use "mail" it goes thru without the error. Any ideas??

2. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution...

3. IP Networking

How to down interface without name

Hi, ifconfig -a return: eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0 ...

4. Shell Programming and Scripting

Mailx: How to send a attachment using mailx command

Hi All, Can anyone please provide the command for sending an mail with attachment using mailx command. Thanks in Advance :) Regards, Siram.

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

8. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance.

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT REDHAT

xvungrabport

XvUngrabPort(3X)														  XvUngrabPort(3X)

Name
       XvUngrabPort - release port grabbed for video operation

Syntax
       #include <X11/extensions/Xvlib.h>

       XvUngrabPort(dpy, port, time)

       Display *dpy;
       XvPortID port;
       Time time;

Arguments
       dpy	      Specifies  the  display  screen  on which the Xv Server is to accept requests from Xv clients.  If the display option is not
		      specified, Xv uses the display screen specified by your DISPLAY environment variable.  The display  option  has  the  format
		      hostname:number.	Using two colons (::) instead of one (:) indicates that DECnet is to be used for transport.

       port	      Specifies the port to be released.  If the port had not been previously grabbed, the request is ignored.

       time	      Specifies the request timestamp.

Description
       XvUngrabPort(3X) releases a grabbed port.  If time specifies a time before the last XvGrabPort(3X) was executed, the request is ignored.

Returned Values
       [Success]
	       Returned if XvUngrabPort(3X) completed successfully.

       [XvBadExtension]
	       Returned if the Xv extension is unavailable.

       [XvBadAlloc]
	       Returned if XvUngrabPort(3X) failed to allocate memory to process the request.

Diagnostics
       [XvBadPort]
	       Generated if the requested port does not exist.

See Also
       XvGrabPort(3X)

XFree86 						       Version Version 4.3.0						  XvUngrabPort(3X)