Can mailx use a specified interface? Post: 302100406

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

mailx error message : mailx: NUL changed to @

If I use the "Mail" link instead of the "mail" link to ../mailx I get this error. Mail so-n-so @whatever.com mailx: NUL changed to @ Unknown command: "postmaster" The email still goes through but i get the error. If I use "mail" it goes thru without the error. Any ideas??

2. Solaris

no such interface

Hi Community, I've a problem with an interface of my Sun Workstation: when I try to plumb hme0 interface I see this output: # ifconfig hme0 <ip_address> netmask <mask> plumb #ifconfig: plumb: hme0: no such interface I've the same thing with dhcp service. could you provide any solution...

3. IP Networking

How to down interface without name

Hi, ifconfig -a return: eth0 Link encap:Ethernet HWaddr 00:09:3D:12:9D:5A inet addr:172.19.208.7 Bcast:172.19.208.63 Mask:255.255.255.192 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:211478649 errors:0 dropped:0 overruns:0 frame:0 ...

4. Shell Programming and Scripting

Mailx: How to send a attachment using mailx command

Hi All, Can anyone please provide the command for sending an mail with attachment using mailx command. Thanks in Advance :) Regards, Siram.

5. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

6. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

7. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

8. UNIX for Dummies Questions & Answers

Interface

Hi All, How to check whether a Interface has a single port or dual port.Thanks in advance.

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT DEBIAN

sendmailconfig

SENDMAILCONFIG(8)					      System Manager's Manual						 SENDMAILCONFIG(8)

NAME

       sendmailconfig - configure sendmail for Debian systems

SYNOPSIS

       sendmailconfig [--no-reload]

DESCRIPTION

       sendmailconfig is used to simplify the configuration of sendmail(8) for use on Debian systems.

       In  the	simplest  case,  you  may  run	this program to (re)configure sendmail for your Debian system at any time. It will modify the file
       /etc/mail/sendmail.mc in order to create a working sendmail configuration which will be written to the file /etc/mail/sendmail.cf.

       For advanced configurations, you can modify the sendmail.mc file before generating sendmail.cf. Future invokations of  sendmailconfig  will
       preserve these changes provided they are made at the end of the file.

       Normally  sendmailconfig  will  ask  if	you want to reload sendmail after making changes to its configuration. The --no-reload option will
       avoid this question.

FILES

       /etc/mail/sendmail.mc
	      sendmail m4 input to generate sendmail.cf

       /etc/mail/sendmail.cf
	      actual sendmail configuration file

       /etc/mail/sendmail.cw
	      names for which we will accept mail in the standard configuration

       /etc/mail/sendmail.ct
	      names of trusted users in the standard configuration

SEE ALSO

       sendmail(8)

AUTHOR

       Robert Leslie <rob@mars.org>

								    21-Jan-1997 						 SENDMAILCONFIG(8)