11-13-2006
The system clock sends out signals to keep everything in sync. The cpu frequency is how fast the cpu can do stuff. Your cpu frequency is 1281 Mhz and your system clock is 183 Mhz. Note that 183 * 7 = 1281. The CPU will keep its clock synced up to the system clock. All of the clocks in your system will be created by multiplying or dividing the system clock by some small integer. The cpu's all plug into a bus. And memory plugs into the same bus. This bus almost always runs at the system clock rate.
10 More Discussions You Might Find Interesting
1. Solaris
Hello Guys, :confused:
I have tried Up to my Levels
pls help me if u know any solution
Pls look out the following O/P,
Log Messages
=================================================
SUN> pwd
/usr/platform/SUNW,Sun-Fire-V240/sbin
SUN>
SUN>
SUN> prtdiag -v
bash: prtdiag: command not... (7 Replies)
Discussion started by: sure.solaris
7 Replies
2. Solaris
hi,
we have an e6900 and my sys admin says that the number of processors and memory were reduced to 4 and 8GB. However, a prtdiag |grep Memory returns 16GB of memory. So what is my system's memory? psrinfo returns 4 online and 4 offline CPUs.
Thanks.
Kumar (1 Reply)
Discussion started by: kumar27
1 Replies
3. Solaris
Hi,
Recently installed a Firmware patch on T5120 (solaris 10,138888-03).
The patch installation was Success and system came up fine as well. My apps are running fine too.
Problem is prtdiag does not work as it used to earlier. the output is very different from other t5120s I have and... (1 Reply)
Discussion started by: upengan78
1 Replies
4. Solaris
Hi, a couple of T2000 servers did not show the component status and the output was too short. There was a patch that needed to be installed. I also updated to the latest recommended patch cluster and OBP patch.
After reboot/restart of picl, it worked ok for a couple of weeks. Then suddenly it went... (12 Replies)
Discussion started by: incredible
12 Replies
5. UNIX for Advanced & Expert Users
Dear All....Help required
prtdiag -v command shows no output on my V440 server.
Following is the details:
root@sdp16b>prtdiag -v
root@sdp16b>
root@sdp16b>uname -a
SunOS sdp16b 5.9 Generic_122300-31 sun4u sparc SUNW,Sun-Fire-V440
root@sdp16b>echo $path
/usr/sbin /usr/bin /usr/sbin... (6 Replies)
Discussion started by: Junaid
6 Replies
6. UNIX for Dummies Questions & Answers
I am having trouble figuring this one out.....Is this a 2CPU or a 4CPU v490 with 16GB? I think it is a 2CPU system, looking for confirmation.
$ prtdiag
System Configuration: Sun Microsystems sun4u Sun Fire V490
System clock frequency: 150 MHz
Memory size: 16384 Megabytes
... (1 Reply)
Discussion started by: config_boy
1 Replies
7. Solaris
Hi. I have 2 SunFire V490 servers running Solaris 10. We may have to upgrade with more memory on one of them to make it compatible with the other. Here's the one with 12GB of RAM:
Memory size: 12288 Megabytes
========================= CPUs ===============================================
... (1 Reply)
Discussion started by: th1amigo
1 Replies
8. Solaris
Hello,
I was under the impression that the Header of the prtdiag output shows the hardware vendor information in the section between System Configuration and sun4u/sun4us. But on some Solaris machines which are running on Fujitsu hardware, the vendor is shown as Sun Microsystems in this... (8 Replies)
Discussion started by: chattygk
8 Replies
9. Solaris
Hi everyone,
Please can you tell me what kind of memro we are talking about when we run :
prtdiag -v
Memory size: 98016 Megabytes
Thank you (7 Replies)
Discussion started by: adilyos
7 Replies
10. Solaris
selected lines from the output of the "prtdiag -v" command on a T5240 SUN server running Solaris 10.
Are the following known as FRU names and what do they mean?
MB/CMP0/BR0/CH0/D0
MB/CMP0/BR0/CH1/D0
SYS/FANBD0/FM0/F0
SYS/FANBD0/FM0/F1
SYS/MB/CMP0/BR1/CH0/D1 ... (1 Reply)
Discussion started by: snoman1
1 Replies
LEARN ABOUT OPENDARWIN
prtdiag
prtdiag(1M) prtdiag(1M)
NAME
prtdiag - display system diagnostic information
SYNOPSIS
/usr/sbin/prtdiag [-v] [-l]
prtdiag displays system configuration and diagnostic information on sun4u and sun4v systems.
The diagnostic information lists any failed field replaceable units (FRUs) in the system.
The interface, output, and location in the directory hierarchy for prtdiag are uncommitted and subject to change in future releases.
prtdiag does not display diagnostic information and environmental status when executed on the Sun Enterprise 10000 server. See the
/var/opt/SUNWssp/adm/${SUNW_HOSTNAME}/messages file on the system service processor (SSP) to obtain such information for this server.
The following options are supported:
-l Log output. If failures or errors exist in the system, output this information to syslogd(1M) only.
-v Verbose mode. Displays the time of the most recent AC Power failure, and the most recent hardware fatal error information, and (if
applicable) environmental status. The hardware fatal error information is useful to repair and manufacturing for detailed diagnos-
tics of FRUs.
The following exit values are returned:
0 No failures or errors are detected in the system.
1 Failures or errors are detected in the system.
2 An internal prtdiag error occurred, for example, out of memory.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWkvm |
+-----------------------------+-----------------------------+
|Interface Stability |Unstable* |
+-----------------------------+-----------------------------+
*The output is unstable.
modinfo(1M), prtconf(1M), psrinfo(1M), sysdef(1M), syslogd(1M), attributes(5), openprom(7D)
NOTES
Not all diagnostic and system information is available on every Solaris platforn, and therefore cannot be displayed by prtdiag. On those
platforms, further information can be obtained from the System Controller.
29 Aug 2005 prtdiag(1M)