11-06-2006
the flashcopy devices should still exist in your system as "defined" when you remove them from your system (check with lsdev -Ccdisk) when they are defined its ok and they keep their hd number even if they are deleted and there are new disks
if they are not defined, check your "disable" script
you have to remove them with rmdev -l and not with rmdev -dl which removes them completely from the odm
Last edited by funksen; 11-06-2006 at 03:16 PM..
10 More Discussions You Might Find Interesting
1. AIX
I have a P570 that for some reason is not allowing the P1-T6 NIC to be recognized. I have confirmed from the HMC that it is set for the LPAR, but when I do a cfgmgr, it won't recognize it. It though is recognizing the slot cards just fine which are P1-C3 for one shelf and P1-C3 of another shelf.... (1 Reply)
Discussion started by: LegendMan
1 Replies
2. AIX
Hi All,
I remember my old senior mentor in AIX that cfgmgr should not be terminated on your console. Because if it's terminated in the middle, the odm might get corrupted.
Is that true for AIX 5.x?
Regards,
itik (1 Reply)
Discussion started by: itik
1 Replies
3. AIX
Hi all,
I have a System i server with a couple of AIX LPARs.
One of the LPARs owns a dual-channel scsi adapter to which I connect a tape library (IBM TS3100) and a DVD Drive.
I had some problems to get the Tape Library detected but finally I got it:
rmt0 Available 03-08-01-4,0 IBM 3580... (1 Reply)
Discussion started by: wendelalexis
1 Replies
4. AIX
OS: AIX 6.1
The host has a dual port NIC installed and when I went to run `cfgmgr -v` to configure it I got an error showing device packages are missing from the install:
`cfgmgr -v` on 10.15.xx.xxx
cfgmgr: 0514-621 WARNING: The following device packages are required for device support but... (3 Replies)
Discussion started by: b1f30
3 Replies
5. Programming
i wrote a tiny version of tail command using a large buffer statically allocated but, in a second time, i found another version in which i use a bidimensional array dynamically allocated.
here is the first version
/*my tiny tail, it prints the last 5 line of a file
*/
#include<stdio.h>... (4 Replies)
Discussion started by: lucasclaus
4 Replies
6. AIX
Hi
When I run cfgmgr -v in my aix box I get the below error :
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.
devices.loopback
My oslevel is 6100-06-02-1044
Please assist.
Please use and tags when... (3 Replies)
Discussion started by: samsungsamsung
3 Replies
7. AIX
Dear all
i have a sun SL500 tape library attached to my AIX box while issue the command cfgmgr i have the below issue
test>cfgmgr
cfgmgr: 0514-621 WARNING: The following device packages are required for
device support but are not currently installed.
devices.fcp.changer
please... (3 Replies)
Discussion started by: thecobra151
3 Replies
8. Solaris
Hi guys!
Could you tell me what's this figure about? (See the attached figure below.)
This is a representation of block allocation filesystem and extent allocation filesystem in Solaris.
Does this mean that in a block-based allocation, data are placed in individual blocks while in... (0 Replies)
Discussion started by: arah
0 Replies
9. AIX
Hi,
From the man page, cfgmgr configures devices and optionally installs device software by running the programs specified in the Configuration Rules object class and it is not dependent on platform .
Are there any fundamental differences impacting the speed of cfgmgr on a stand-alone and... (5 Replies)
Discussion started by: Sachin1987
5 Replies
10. Post Here to Contact Site Administrators and Moderators
Hi,
My AIX server able to detect the LUN's which is mapped from IBM v7k storage, And i allocated one more LUN from HP storage but it's appear two hdisk instead of one and it's showing incorrect LUN ID.
SDDPCM driver already installed on this server.
During cfgmgr, Im getting this message :... (1 Reply)
Discussion started by: xinuadmin
1 Replies
LEARN ABOUT DEBIAN
mkqdisk
mkqdisk(8) Quorum Disk Management mkqdisk(8)
NAME
mkqdisk - Cluster Quorum Disk Utility
WARNING
Use of this command can cause the cluster to malfunction.
SYNOPSIS
mkqdisk [-?|-h] | [-L] | [-f label] [-c device -l label] [-d [-d ...]]
DESCRIPTION
The mkqdisk command is used to create a new quorum disk or display existing quorum disks accessible from a given cluster node.
OPTIONS
-c device -l label
Initialize a new cluster quorum disk. This will destroy all data on the given device. If a cluster is currently using that device
as a quorum disk, the entire cluster will malfunction. Do not run this on an active cluster when qdiskd is running. Only one
device on the SAN should ever have the given label; using multiple different devices is currently not supported (it is expected a
RAID array is used for quorum disk redundancy). The label can be any textual string up to 127 characters - and is therefore enough
space to hold a UUID created with uuidgen(1).
-f label
Find the cluster quorum disk with the given label and display information about it.
-L Display information on all accessible cluster quorum disks.
-d Increase debugging level. Specify multiple times for more information. Currently, specifying more than twice has no effect.
SEE ALSO
qdisk(5), qdiskd(8), uuidgen(1)
July 2006 mkqdisk(8)