11-01-2006
hi,
> ...server dont have the route to reach your 10.1.x.x/10.7.x.x network.
yes, that's right. and that is exactly what i was asking for in my original post...on the second NIC in the FreeBSD machine, I need to set a default gateway to 10.10.10.1. However, the rc.conf file only seems to allow me to set one default router and that config entry currently sets the default route for the first NIC. how do I set a default route for the second NIC in the rc.conf file?
10 More Discussions You Might Find Interesting
1. AIX
Hi friends,
I installed oracle 10g (10.2.0.2) RAC on 2 IBM p5 570 servers running AIX 5.3ML04 and HACMP5.2 (used Raw devices, not used GPFS). Each server has 4 x 1Gbps ethernet cards (NICs), en0 and en1 for boot address, en2 and en3 for oracle interconnect.
Now i want to merge 2 NICs (en2 and... (1 Reply)
Discussion started by: bong02
1 Replies
2. Solaris
Hi, is there a way in Solaris 8 to determine how many total NIC's say a Sun Sparc box has installed - plumbed or unplumbed - and find out its capable network speeds and MAC address?
I know ifconfig -a but that only shows the plumbed and used interfaces.
thx
cc (2 Replies)
Discussion started by: bigapple100
2 Replies
3. Linux
I'm looking for a way in RHL 5.1 to use two NICs on one host with two physical IP addresses and map them under one virtual IP address, i.e. NIC 1 10.10.10.1 NIC2 10.10.10.2 VIP 192.168.10.1
Basically I want either one of the NICs to ARP for the VIP. No load balancing required just HA. (2 Replies)
Discussion started by: wschmied
2 Replies
4. IP Networking
I had the pleasure of having a gig nic given to me this week, which also appears on the hardware list of FreeBSD.
What I would LIKE to do is:
1). Set my 10/100 nick as the dedicated outside/internet connection with a lan ip of 192.168.1.100
2). Set the gig nick as the dedicated... (2 Replies)
Discussion started by: droolin
2 Replies
5. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
6. UNIX for Dummies Questions & Answers
Help, I have a Ubuntu headless server that has 5 NICs in it. The eth0-4 interfaces keep moving from NIC to NIC on boot up. I am told that there is a file that I can edit that will allow me to stabilize this but I need some help in determining the exact file and format for that file. All help will... (0 Replies)
Discussion started by: poundjd
0 Replies
7. Red Hat
I don't undestand how to combine 4 nics in order to use DM Multipath. Do I have to install each nic with its IP address? If yes, do I need a group IP address? This concept is not clear for me.
The connection beetwen the server (DELL Poweredge T710) and the SAN through iscsi works well, I used... (1 Reply)
Discussion started by: gnupinux
1 Replies
8. Hardware
Hi,
I have to get into BIOS and disable onbaord NICS for an IBM server, can someone please help me out.
I tried hitting F1 when reboot to get into BIOS, but it seems like a setup screen and I dont see any option to disable NICS?
Thanks
Sam (2 Replies)
Discussion started by: sam4919
2 Replies
9. IP Networking
Hi all,
Host - Ubuntu 12.04 desktop 64bit
Virtualizer - Oracle VirtualBox
2 NICs
Where can I find relevant document to set up 2 NICs, one for inward bound and another for outward bound, separate channel, both connected to the same router
Would following document be appropriate for my... (1 Reply)
Discussion started by: satimis
1 Replies
10. UNIX for Dummies Questions & Answers
Hello All,
I have Linux box with two interface cards.
Every card has it's own IP Address and Gateway, IP addresses are from different subnets.
eth0 192.168.1.10/24 GW 192.168.1.1
eth1 192.168.2.10/24 GW 192.168.2.1
Third PC is located in 192.168.13.0/24 network and is trying to access... (2 Replies)
Discussion started by: AndreiM
2 Replies
LEARN ABOUT DEBIAN
make_sockdfr
MAKE_SOCKDFR(8) System Manager's Manual MAKE_SOCKDFR(8)
NAME
make_sockdfr - Generates frozen route file for SOCKS server
SYNOPSIS
make_sockdfr [infile [outfile] ]
DESCRIPTION
make_sockdfr reads in a plain-text route file for the SOCKS server and produces a frozen route file as the output.
Both arguments are optional. The default for infile is /etc/sockd.route; the default for outfile is /etc/sockd.fr. You may specify infile
while omitting outfile, but you cannot specify outfile without also speficying infile.
The contents of the frozen route file is essentially the memory image of the parsed input file. Using the frozen route file can reduce the
start-up delay of the SOCKS server program since it no longer has to parse the file contents.
When the SOCKS server starts, it always looks for the frozen route file /etc/sockd.fr first. If that file is not found, it then tries to
use the plain-text route file /etc/sockd.route. If you use frozen route file, you must remember to run make_sockdfr every time after you
modify the plain-text file or the SOCKS server will continue to use the frozen version of a previous route file.
To find out the contents of a frozen route file, use dump_sockdfr.
FILES
/etc/sockd.fr, /etc/sockd.route
SEE ALSO
dump_sockdfr(8), sockd.fr(5), sockd.route(5)
AUTHOR
Ying-Da Lee, yingda@esd.sgi.com or yingda@best.com
May 6, 1996 MAKE_SOCKDFR(8)