10-26-2006
Unable to bring up Sun OS
The last thing I did was set REMOTE_LOGIN_PASSWORDFILE to EXCLUSIVE. Then rebooted server. Since that time I have not been able to login. During bootup it can't find root and generates alot of errors. Does anybody know of a default login and password that will allow me to log in and rebuild the password file? It's either that or I will need to find a boot recovery CD.
Bill
9 More Discussions You Might Find Interesting
1. IP Networking
I have Linux 7.1 setup on a Dell and am unable to bring up any interfaces. Both the lo and eth0 fail upon boot up and I get a insmod error possibly due to bad irq or IO setting.
If I disable eth0 upon boot, then lo works fine, but offcourse I get the "delaying initialization" upon boot for eth0... (1 Reply)
Discussion started by: alam
1 Replies
2. IP Networking
I tried to telnet to my Sun server (E250) but I received the error message :
"Network error: Connection reset by peer".
I was able to ping my server. And, I had already commented off "CONSOLE=/dev/console" in /etc/default/login.
But, if I rlogin from all other servers, it works.
Is there... (2 Replies)
Discussion started by: dawn_lwf
2 Replies
3. Solaris
Greetings,
I have recently inherited 3 sun servers from a shop that my parent company closed. One of these servers is an old Ultra 1 running SunOS 5.6 that acts as a NIS server for the other two servers. This NIS server seems to boot OK and function properly as a NIS server. However, I can't... (6 Replies)
Discussion started by: SevenFortyOne
6 Replies
4. Shell Programming and Scripting
hi experts,
I m new to the sun solaris.
on our OS (sun solaris 5.8) i m trying to send mail but i not getting any mail, i have tried doing following .
$mailx -s "Test" sivakumars@kesd.com
But no response there no error also...
pls let me know:
1) How can test sending mail through... (3 Replies)
Discussion started by: saisivakumar
3 Replies
5. Solaris
Hello experts.
I am using Solaris 10(2005) on intel machine. I have installed Veritas Volume manager 5.0. I am unable to bring a disk error to online state. I would like to bring that disk to CDS format.
Commands i used and output are....
#vxdisk list
DEVICE TYPE ... (11 Replies)
Discussion started by: younus_syed
11 Replies
6. Solaris
Hi :
I have a e450 sun server that I just started up and I connect my laptop to the serial connection using a null modem cable and it just does not connect.
I use hyperterminal, I dont connect a keyboard to the sun machine?
Any ideas?
Thanks a lot
Al (3 Replies)
Discussion started by: alanj4
3 Replies
7. Hardware
I have a problem with one of my Sun 280R servers.
I'm unable to boot it. I've managed to get to the {ok} prompt from the RSC card.
Please see output below
ok show-devs
/virtual-memory
/memory
/aliases
/options
/openprom
/chosen
/packages
/openprom/client-services... (2 Replies)
Discussion started by: soliberus
2 Replies
8. Solaris
this is samiulla
in my vmware solaris 11 i installed iscsitgt pakage but it goes to maintenance
and i am unable to bring into online with svcadm clear iscsitgt
how can i forcefully online iscsitgt service. (1 Reply)
Discussion started by: samiulla
1 Replies
9. Solaris
Hi,
I am unable to connect sun server, server model is sun fire v440
on server 2 ports are there.
serial management, and network management.
I would like to know how to connect serial port if I dont have com port on my system? and on Network Management no ip address is configured.
... (2 Replies)
Discussion started by: manoj.solaris
2 Replies
LEARN ABOUT MINIX
rem_drv
rem_drv(1M) rem_drv(1M)
NAME
rem_drv - remove a device driver from the system
SYNOPSIS
rem_drv [-b basedir] device_driver
The rem_drv command informs the system that the device driver device_driver is no longer valid. If possible, rem_drv unloads device_driver
from memory. rem_drv also updates the system driver configuration files.
If rem_drv has been executed, the next time the system is rebooted it automatically performs a reconfiguration boot (see kernel(1M)).
The following options are supported:
-b basedir Sets the path to the root directory of the diskless client. Used on the server to execute rem_drv for a client. The client
machine must be rebooted to unload the driver.
Note - The root file system of any non-global zones must not be referenced with the -b option. Doing so might damage the
global zone's file system, might compromise the security of the global zone, and might damage the non-global zone's
file system. See zones(5).
Example 1: Removing the sd Driver
The following example removes the sd driver from use:
example% rem_drv sd
Example 2: Removing a Diskless Client
The following example removes the driver from the sun1 diskless client. The driver is not uninstalled or unloaded until the client machine
is rebooted.
example% rem_drv -b /export/root/sun1 sd
Note the caveat on the use of the -b option in the description of that option, above.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
add_drv(1M), kernel(1M), update_drv(1M), attributes(5), devfs(7FS)
6 Apr 2005 rem_drv(1M)