10-20-2006
Yep. Select the Minimum Configuration option and it's a couple of lines from the bottom. Select F6 to see the command line for setting the info (/usr/sbin/mktcpip). I do that to see what the command line looks like and then run man mktcpip (in this case) to try and understand the command better.
Carl
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I want to block ping on a linuxbox to any other address where it would go to the default gateway.
vmdebianamd64:/etc/tcng# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
198.9.200.0 * 255.255.255.0 U 0 ... (1 Reply)
Discussion started by: progressdll
1 Replies
2. IP Networking
hi,
I m trying to ping ip on the network . The machine is started but i can't access and can't ping it .. But when i restarts that machine that works fine..... can anybody have an idea about this problem ??
if then reply ..
thanks (2 Replies)
Discussion started by: tahir23
2 Replies
3. Linux
Hi All,
Need your help one more time.
I am trying to ping a linux machine which is not responding to ping.
However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0".
It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies
4. Linux
I was wondering if it is possible to setup SFTP to go through the internet proxy while connecting to an internet location.
Problem: Client system is behind internet proxy. SFTP to any internet location fails as there is no documented way to configure SFTP to connect to internet locations through... (4 Replies)
Discussion started by: toobrown1
4 Replies
5. Debian
Hi,
I have my router (192.168.1.1) connected to the internet.
I have installed Debian on a server with Bind9 (192.168.1.254).
The configurations files are :
$ cat /etc/network/interfaces
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface... (1 Reply)
Discussion started by: Thibault
1 Replies
6. Solaris
Hi,
I was trying to ping the source and destination i.ps
ping -i <source> <destination>
<destination> is alive
Now i would like to see the packets contiuosly. Please suggest what option can be used with ping command to see
For example if i give
PING 10.137.58.78: 56 data bytes
64... (3 Replies)
Discussion started by: kkarthik_kaja
3 Replies
7. Shell Programming and Scripting
Hi,
I develop simple animation ping script on Solaris Platform. It is like Cisco ping.
Examples and source code are below.
bash-3.00$ gokcell 152.155.180.8 30
Sending 30 Ping Packets to 152.155.180.8
!!!!!!!!!!!!!.!!!!!!!!!!!!!!!.
% 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies
8. IP Networking
I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies
9. Shell Programming and Scripting
Hi
I am using perl to ping a list of nodes - with script below :
$p = Net::Ping->new("icmp");
if ($p->ping($host,1)){
print "$host is alive.\n";
}
else {
print "$host is unreacheable.\n";
}
$p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies
10. Programming
help with bash script!
im am working on this script to make sure my server will stay online, so i made this script..
HOSTS="192.168.138.155"
COUNT=4
pingtest(){
for myhost in "$@"
do
ping -c "$COUNT" "$myhost" &&return 1
done
return 0
}
if pingtest $HOSTS
#100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies