Sponsored Content
Special Forums IP Networking Can't ping internet. Need help Post 302093567 by rhfrommn on Friday 20th of October 2006 11:37:22 AM
Old 10-20-2006
Looks to me like you're missing a default router. Try netstat -nr and see if a default route is listed. If not, use smit to set one.
 

10 More Discussions You Might Find Interesting

1. UNIX for Advanced & Expert Users

iptables rule to block ping to internet

I want to block ping on a linuxbox to any other address where it would go to the default gateway. vmdebianamd64:/etc/tcng# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 198.9.200.0 * 255.255.255.0 U 0 ... (1 Reply)
Discussion started by: progressdll
1 Replies

2. IP Networking

can't ping by ip

hi, I m trying to ping ip on the network . The machine is started but i can't access and can't ping it .. But when i restarts that machine that works fine..... can anybody have an idea about this problem ?? if then reply .. thanks (2 Replies)
Discussion started by: tahir23
2 Replies

3. Linux

Not able to ping

Hi All, Need your help one more time. I am trying to ping a linux machine which is not responding to ping. However traceroute can reach the machine and I can log in to it by ssh. I have checked /proc/sys/net/ipv4/icmp_echo_ignore_all it is already set as "0". It is not happening in the... (1 Reply)
Discussion started by: ailnilanjan
1 Replies

4. Linux

SFTP an internet address from a system behind an internet proxy

I was wondering if it is possible to setup SFTP to go through the internet proxy while connecting to an internet location. Problem: Client system is behind internet proxy. SFTP to any internet location fails as there is no documented way to configure SFTP to connect to internet locations through... (4 Replies)
Discussion started by: toobrown1
4 Replies

5. Debian

PB : DNS Client don't ping internet

Hi, I have my router (192.168.1.1) connected to the internet. I have installed Debian on a server with Bind9 (192.168.1.254). The configurations files are : $ cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface... (1 Reply)
Discussion started by: Thibault
1 Replies

6. Solaris

Ping

Hi, I was trying to ping the source and destination i.ps ping -i <source> <destination> <destination> is alive Now i would like to see the packets contiuosly. Please suggest what option can be used with ping command to see For example if i give PING 10.137.58.78: 56 data bytes 64... (3 Replies)
Discussion started by: kkarthik_kaja
3 Replies

7. Shell Programming and Scripting

Animation Ping on Solaris Like Cisco Ping

Hi, I develop simple animation ping script on Solaris Platform. It is like Cisco ping. Examples and source code are below. bash-3.00$ gokcell 152.155.180.8 30 Sending 30 Ping Packets to 152.155.180.8 !!!!!!!!!!!!!.!!!!!!!!!!!!!!!. % 93.33 success... % 6.66 packet loss...... (1 Reply)
Discussion started by: gokcell
1 Replies

8. IP Networking

PING

I am unable to ping my remote server.My server is unable to ping the same. both are able to ping the gateway. both the ip's are on same network.i use a proxy tunnel on my remote server.Help if any clues. (6 Replies)
Discussion started by: oslbhavana
6 Replies

9. Shell Programming and Scripting

How to get reason for ping failure using perls Net::Ping->new("icmp");?

Hi I am using perl to ping a list of nodes - with script below : $p = Net::Ping->new("icmp"); if ($p->ping($host,1)){ print "$host is alive.\n"; } else { print "$host is unreacheable.\n"; } $p->close();... (4 Replies)
Discussion started by: tavanagh
4 Replies

10. Programming

Ping test sends mail when ping fails

help with bash script! im am working on this script to make sure my server will stay online, so i made this script.. HOSTS="192.168.138.155" COUNT=4 pingtest(){ for myhost in "$@" do ping -c "$COUNT" "$myhost" &&return 1 done return 0 } if pingtest $HOSTS #100% failed... (4 Replies)
Discussion started by: mort3924
4 Replies
defaultrouter(4)                                                   File Formats                                                   defaultrouter(4)

NAME
defaultrouter - configuration file for default router(s) SYNOPSIS
/etc/defaultrouter DESCRIPTION
The /etc/defaultrouter file specifies a IPv4 host's default router(s). The format of the file is as follows: IP_address ... The /etc/defaultrouter file can contain the IP addresses or hostnames of one or more default routers, with each entry on its own line. If you use hostnames, each hostname must also be listed in the local /etc/hosts file, because no name services are running at the time that defaultrouter is read. Lines beginning with the ``#'' character are treated as comments. The default routes listed in this file replace those added by the kernel during diskless booting. An empty /etc/defaultrouter file will cause the default route added by the kernel to be deleted. Use of a default route, whether received from a DHCP server or from /etc/defaultrouter, prevents a machine from acting as an IPv4 router. You can use routeadm(1M) to override this behavior. FILES
/etc/defaultrouter Configuration file containing the hostnames or IP addresses of one or more default routers. SEE ALSO
in.rdisc(1M), in.routed(1M), routeadm(1M), hosts(4) SunOS 5.10 17 Aug 2004 defaultrouter(4)
All times are GMT -4. The time now is 04:33 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy