Sponsored Content
Full Discussion: V890 Benefits over V880
Top Forums UNIX for Advanced & Expert Users V890 Benefits over V880 Post 302092425 by reborg on Monday 9th of October 2006 06:37:43 PM
Old 10-09-2006
The difference between an 880 and an 890 is the fact that the 890 uses SPARC IV dual core CPUs, these can be either 'plain' IV or IV+. There is a speed increase with the IV and IV+ cpus in addition to the fact that they are dual core. Effectively this means that an 890 has > twice the compute power or an equivalently populated 880. Additionally is is possible to get a RoHS confroming 890 whereas you cannot get an 880 which conforms to the standard.
 

6 More Discussions You Might Find Interesting

1. Solaris

Installing Solaris 8 on a V890

Question, I have a new V890 preloaded witrh Solaris 10. Due to SW compatibility I need to run Sol 8 on the server. When running boot cdrom from the ok prompt, I get amessages looking for a location on the CDROM to find the startup install SW. The path must be different from what's on Sol 10 install... (4 Replies)
Discussion started by: stocksj
4 Replies

2. UNIX for Dummies Questions & Answers

What are some benefits of the UNIX hierarchical file structure?

What are some benefits of the UNIX hierarchical file structure? I am new to UNIX and researching some information about it for a class so please help if you can. Thanks. (1 Reply)
Discussion started by: 88923JJJSDK
1 Replies

3. Solaris

HBA problem...? at SF V890

Dear All, I need your help. I have server like this SunOS 5.10 Generic_141444-09 sun4u sparc SUNW,Sun-Fire-V890 with messages like this... Oct 10 17:07:52 iscsi: NOTICE: unrecognized ioctl 0x403 Oct 10 17:07:52 scsi: WARNING: /pseudo/fcp@0 (fcp0): Oct 10 17:07:52 Invalid... (4 Replies)
Discussion started by: mbah_jiman
4 Replies

4. Solaris

Solaris Volume Manger - Database Replicas Question - Benefits of Increasing Default Size?

Hey all! I was hoping someone knew anything about this one... I know with Solaris Volume Manager the default Database Replica size is 8192 blocks (4MB approximately) Now I know you can increase this amount but is there any point? The reason I am asking this is that I've setup mirroring on... (2 Replies)
Discussion started by: Keepcase
2 Replies

5. Solaris

v890 cannot boot

I just received a v890. I cannot get it to boot via CDROM nor can I access the SC prompt because I do not know the password. I am attempting to access it via serial cable to a Linux box. What is the best way to proceed? (25 Replies)
Discussion started by: LittleLebowski
25 Replies

6. Solaris

Could you run this benchmark? (Especially if you have a V880 or V890)

Hi all I am currently using a T5120 to write and run some simulation code I've been working on which heavily relies on large matrix multiplication procedures. I am posting this to call out for some of you run and share the results of a simple benchmark I've written to compare the matrix... (1 Reply)
Discussion started by: toguro123
1 Replies
NEWAPC(8)						      Network UPS Tools (NUT)							 NEWAPC(8)

NAME
newapc - Driver for American Power Conversion Smart Protocol UPS equipment NOTE
This man page only documents the hardware-specific features of the newapc driver. For information about the core driver, see nutupsdrv(8). SUPPORTED HARDWARE
newapc should recognize all recent APC models that use a serial protocol at 2400 bps. This is primarily the Smart-UPS, Matrix-UPS and Back-UPS Pro lines. Older APC models may work better with the apcsmart driver. The driver attempts to support every bell and whistle of the APC reporting interface, whether or not this is strictly sensible. Some older hardware may only report a handful of variables. This is usually not a bug - they just don't support anything else. CABLING
This driver expects to see a 940-0024C cable or a clone by default. You can switch to the 940-0095B dual-mode cable support with the cable= definition described below. If your 940-0024C cable is broken or missing, use this diagram to build a clone: http://www.exploits.org/nut/library/cables/940-0024C.jpg EXTRA ARGUMENTS
This driver supports the following optional settings in the ups.conf(5): cable=940-0095B Configure the serial port for the APC 940-0095B dual-mode cable. sdtype=num Use shutdown type num, according to this table: 0: soft shutdown or powerdown, depending on battery status 1: soft shutdown followed by powerdown 2: instant power off 3: power off with grace period Modes 0 and 1 will power up the load when power returns. Modes 2 and 3 will keep the load turned off when the power returns. BUGS
Some older APC UPS models return bogus data in the status register during a front panel test. This is usually detected and discarded, but some other unexpected values have occasionally slipped through. AUTHOR
Nigel Metheringham <Nigel.Metheringham@Intechnology.co.uk> (drawing heavily on the apcsmart driver by Russell Kroll). SEE ALSO
The core driver: nutupsdrv(8) The apcsmart driver: apcsmart(8) Internet resources: The NUT (Network UPS Tools) home page: http://www.exploits.org/nut/ NUT mailing list archives and information: http://lists.exploits.org/ Tue Oct 22 2002 NEWAPC(8)
All times are GMT -4. The time now is 10:25 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy