Sponsored Content
Full Discussion: Where are routes stored ?
Operating Systems Solaris Where are routes stored ? Post 302091674 by BOFH on Wednesday 4th of October 2006 12:13:29 PM
Old 10-04-2006
If it's a manual addition, check /etc/init.d or /etc/rc2.d and see if there's a local file. The group I was with had a S96local script with specific route additions. You can also just grep the "add net" in the init.d directory to find the file if it's something else.

Carl
 

10 More Discussions You Might Find Interesting

1. IP Networking

Multiple Interfaces and Routes

I have a Unix box with 2 network interfaces on the same IP subnet and would like to add a host route via a specific interface. Any assistance would be greatly appreciated. (3 Replies)
Discussion started by: diemos
3 Replies

2. Debian

Setting Routes and such

Ok, I made changes to my routing tables..... which file do I modify to make the routes initialize correctly when the machine boots up? I work with all flavours of Unix/Linux... but this is an older box... Linux, Release 2.2.14-5.0. I did a grep for the default route in /etc, but didnt find... (2 Replies)
Discussion started by: djsal
2 Replies

3. AIX

Multiple Default routes

Hi All, I have a AIX server running v5.2 and its having multiple default routes configured to two seperate gateway. Here's the output of -- netstat -rn Routing tables Destination Gateway Flags Refs Use If PMTU Exp Groups Route Tree for Protocol Family 2... (2 Replies)
Discussion started by: rramanuj
2 Replies

4. Solaris

adding routes in Solaris

Solaris Guru's What is the proper way to add routes in the routing table so after a node reboot the routes will not be lost. I understand the /etc/defaultrouter for the default router and the <route add> command but using this command routes will be removed once the node reboots. Thanks (7 Replies)
Discussion started by: Brad_52000
7 Replies

5. IP Networking

How to delete some ipv6 routes?

Hi, How can i delete the following routes on my OpenBSD 4.1 system? # route -n show (including only relevant ipv6-routes) Internet6: Destination Gateway Flags Refs Use Mtu Interface ::/104 ::1 UGRS 1 0 ... (1 Reply)
Discussion started by: phalcos
1 Replies

6. AIX

Static Routes question

I added a static route through smit using: Communications applications and Services ==> TCIP/IP ==> Further Configuration ==> Static Routes ==> Add a Static Route ==> Route Type of host Filled in Destination Address, Default Gateway Address and Network Interface of en0. This... (2 Replies)
Discussion started by: jyoung
2 Replies

7. UNIX for Dummies Questions & Answers

Routes being automatically added

Hello, I have two AIX 5.3 servers that are supposedly set up exactly the same. The problem I am having is on one of the servers, it seems dynamic routes are being added mysteriously and non-periodically. This only happens on one server and not the other. Also, there doesn't seem to be a specific... (1 Reply)
Discussion started by: Conutmonky
1 Replies

8. IP Networking

Unix Network Routes

I would really appreciate some help with HP UX's Network Routes. Basically, what I want to do is, I would want a system with global ip (eg: 202.144.138.122) to ping/access my HP-UX server which is with private IP address (192.168.1.23). I have all the routers/switches in between properly route... (2 Replies)
Discussion started by: damchey
2 Replies

9. SCO

Static routes in SCO

Hi, Just a question of thought. Why one needs to add static routes on Unix servers ? If I had ethernet card, it already has the settings for gateway for incoming and outgoing requests. We donot have to explicitly set the route it should take. Then what is the use... (3 Replies)
Discussion started by: dextergenious
3 Replies

10. Solaris

Problem with routes in Solaris 10

Hello All, I have a Solaris 10 machine with 4 physical network interfaces configured viz. igb0, e1000g0, igb2 and e1000g2. Out of these interfaces, I am routing all my normal monitoring and O&M activities via. igb0 and e1000g0 interfaces. However, I am facing an issue on one of the... (4 Replies)
Discussion started by: mystition
4 Replies
VDE_L3(1)						      General Commands Manual							 VDE_L3(1)

NAME
vde_l3 - Virtual Distributed Ethernet 'Layer 3' Switch. SYNOPSIS
vde_l3 -v vde_plug:ipaddress/netmask [-v...] [-r target_network/netmask:gateway] [-G default_gw] [-M mgmt_socket] DESCRIPTION
A vde_l3 connects to one or more vde_switches, performing ip forwarding among its virtual interfaces. A new interface is created at startup for each -v option given at command line. Static routes to target networks can be defined using the -r option. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 connects to the vde sock at /var/run/s1.ctl with its virtual interface ve0, having the address 192.168.0.1 and netmask 255.255.255.0. vde_l3 -v /var/run/s1.ctl:192.168.0.1/24 -v /var/run/s2.ctl:10.0.0.254/255.255.0.0 connects to the two vde socks, with its virtual interfaces ve0 and ve1, having addressess 192.168.1.0 and 10.0.0.254 respectively. Hosts in each network can specify the vde_l3 as their gateway to reach the other one. OPTIONS
-v vde_plug:ipaddress/netmask Creates a virtual network interfaces on the vde_l3 box, with address ipaddress and netmask netmask. Please note that the netmask can be specified either in the 'classic' A.B.C.D mode, or just by giving the number of leading bits (f.e., /17 for 255.255.128.0). One can define as many interfaces as she wants. -r target_network/netmask:gateway Specify a static route through gateway to reach hosts in target_network with netmask netmask. One can define as many routes as she wants. -G default_gw Specify a default gateway, to be used whenever no static route is defined for a target host. -M mgmt_socket the unix socket where the parameters (interfaces addresses, routes, etc.) can be checked and changed runtime. unixterm(1) can be used as a remote terminal for wirefilter. NOTICE
Virtual Distributed Ethernet is not related in any way with www.vde.com ("Verband der Elektrotechnik, Elektronik und Informationstechnik" i.e. the German "Association for Electrical, Electronic & Information Technologies"). SEE ALSO
vde_switch(1), vdeq(1), unixterm(1), vde_cryptcab(1), wirefilter(1). AUTHORS
VDE_L3 is a tool by Daniele Lacamera <root@danielinux.net> VDE is a project by Renzo Davoli <renzo@cs.unibo.it> Virtual Distributed Ethernet May 7, 2007 VDE_L3(1)
All times are GMT -4. The time now is 06:38 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy