Qlogic 2300 and WWN display Post: 302091081

10 More Discussions You Might Find Interesting

1. Solaris

Wwn

hiho peeps, is there a possibility to see the WWNs of your SAN-HBAs, like in ifconfig the MAC-addresse.....??? greetings Pressy

2. Red Hat

RHEL AS 4 Kernel SRC + DKMS + QLogic

Hi, I need some help. I installed RHEL AS 4 u5 x86_64 (vendor requirement) on a Dell Blade 1855. I have a daughter board that will give it a HBA port. I can't install the daughter card until the Qlogic driver is loaded. I can't install the Qlogic driver sine the kernel src is not there. So I...

3. UNIX for Dummies Questions & Answers

Need to sort/change modify 2300 users ...

Ok, so here's my project I've been given and I know very little about this. I have an AIX unix box that has over 2300 local users. Any user with 4 or less characters in the username does not get changed. Any user with 5 or more needs to have the attribute shell=/bin/ksh changed to...

4. Solaris

Qlogic HBA card in E450 with errors

I have installed a qlogic HBA card in an E450 Solaris 9 with all the SUNW packages and the latest EPROM version. Configuration reboot was done. An orange light flashes to the right of where the card plugs into the fiber cable after booting, and the following error apprears at the start of the boot...

5. Solaris

Qlogic HBA's - lputil / lpfc.conf

Hi all Hope your all well and happy in solaris land :-) Recently purchased some Qlogic HBA's for a few solaris servers. Was told that you cant have mixed chipsets and as this client is all qlogic, have to have hba's using qlogic. 1) Is that correct ? Cant mix different chipsets of...

6. Solaris

Qlogic HBA + Veritas - Part 2

Hi all, New to the world of SAN, so forgive me for any ambigious terminology. I have a sun 6800 chassis with two domains, both domains connected to a San ancor sanbox ( 2 x Storeedge T3 / Mcdata switch ). Current Qlogic HBA's are 1Gb glc adaptors, version of qlc drivers...

7. Red Hat

lun masking at qlogic HBA level

need to do LUN masking at qlogic HBA level..at RHEL 5.x I am using qla* module at part of the Unix kernel, it is not OEM drivers that come with the HBA card, so I can't use Sansurfer to do this.. Is there a way to do this at all ?? :wall:

8. Solaris

Solaris OS having issue accessing LUN from Qlogic swich

Hi Community, I am facing one issue related storage accessing from solaris 10 machine(M5000). it was working fine then we shifted to another site. the only change on that site is FC switch. The issue i am facing is from solaris machine i can able to see the LUN, it;s only a test lun of 30...

9. Solaris

Qlogic 10G Ethernet adapter not working

Hi Community, i have one issue with 10 fiber ethernet adapter. here is my details: root@new-bpel.example.com #dladm show-dev bge0 link: unknown speed: 0 Mbps duplex: unknown bge1 link: up speed: 1000 Mbps duplex: full qlge2 link:...

10. Red Hat

Need WWN

How do I identify the WWN of associated SAN through a logical volume that is mounted on a RHEL 6 system

LEARN ABOUT FREEBSD

qlxge

QLXGE(4)						   BSD Kernel Interfaces Manual 						  QLXGE(4)

NAME

     qlxge -- QLogic 8100 Series 10 Gigabit Ethernet Adapter Driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device qlxge

     To load the driver as a module at boot time, place the following line in loader.conf(5):

	   if_qlxge_load="YES"

DESCRIPTION

     The qlxge driver supports IPv4 checksum offload, TCP and UDP checksum offload for both IPv4 and IPv6, Large Segment Offload for both IPv4 and
     IPv6, Jumbo frames, VLAN Tag, and Receive Side scaling.  For further hardware information, see http://www.qlogic.com/.

HARDWARE

     The qlxge driver supports 10 Gigabit Ethernet & CNA Adapter based on the following chipsets:

     o	 QLogic 8100 series

SUPPORT

     For support questions please contact your QLogic approved reseller or QLogic Technical Support at http://support.qlogic.com, or by E-mail at
     <support@qlogic.com>.

SEE ALSO

     altq(4), arp(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The qlxge device driver first appeared in FreeBSD 10.0.

AUTHORS

     The qlxge driver was written by David C Somayajulu at QLogic Corporation.

BSD
								   June 21, 2013							       BSD