09-28-2006
Post the partition table of c1t0 by going into format, pick disk c1t0, p,p, and copy the output to here.
10 More Discussions You Might Find Interesting
1. Solaris
Hi Guys,
Need to add 2 disks into a JBOD array (3310).
Does anyone see anything wrong with my Procedure / Doco below?
1> Logon to system, check system logs for abnormal entries.
2> Make backups of related system files:
A>cp -p /etc/system /etc/system.backup.081505
B>cp -p /etc/vfstab... (3 Replies)
Discussion started by: BG_JrAdmin
3 Replies
2. UNIX for Advanced & Expert Users
Hello!
I recently inherited system administration duties for a SUN v880 box. The system has 6 physical hard disks.. In doing some basic maintenance, I found they're configured for mirroring. I ran the metastat and metadb commands, and many of the mirrors are showing they are in need of... (5 Replies)
Discussion started by: ghuber
5 Replies
3. Solaris
hi expert,
i had reinstall the sun v890 server solaris 8 and also do mirroring, i had configure the network for the server (hostname.eri0,hosts,netmasks,nodename,etc) after i reboot get and error messages below :
Setting default IPv4 interface for multicast: add net 224.0/4: gateway... (5 Replies)
Discussion started by: bucci
5 Replies
4. Solaris
hi experts,
i have some problem with my server v890, i had config the network with ce0,ce1 and eri0 but after reboot the server have this error messages display :
WARNING: ce0: fault detected external to device; service degraded
WARNING: ce0: xcvr addr:0x01 - link down
configuring IPv4... (2 Replies)
Discussion started by: bucci
2 Replies
5. Solaris
I am having an issue with setting up disk mirroring for Solaris 10 on an x86 server. My main problem is that the volumes and slices have already been setup and our proprietary software has already been installed and configured. The entire drive has been allocated in this configuration and the... (2 Replies)
Discussion started by: chuck43
2 Replies
6. Solaris
Has anyone managed to set up disk mirroring in Solaris 10 yet? If so can you point me in the direction of some useful documentation please.
Cheers (25 Replies)
Discussion started by: korfnz
25 Replies
7. Solaris
Hi Friends,
I am having Sun Solaris 5.8 OS installed having 2 different size hard disk, sizes are c0t0d0s0(160 GB) and c0t2d0s0 (40GB). I have installed Sun Solaris 5.8 OS in c0t0d0s0 (160GB) harddisk.
I have configured all the parameters required for disk mirroring. But when executing... (4 Replies)
Discussion started by: Vijayakumarpc
4 Replies
8. Solaris
Hello Gurus,
Im trying to migrate some SAN disks from sparc server to X86 one, and having issues with disks not getting mounted on the X86 server with " not this fstyp error" due to the different partitions lay out between the two OS. I have tried it from sparc to sparc server and it worked,... (10 Replies)
Discussion started by: aladdin
10 Replies
9. Solaris
Need a procedure document to do "root disk mirroring in solaris volume manager for solaris 10". I hope some one will help me asap. I need to do it production environment.
Let me know if you need any deatils on this.
Thanks,
Rama (1 Reply)
Discussion started by: ramareddi16
1 Replies
10. Solaris
I would like to perform root disk mirroring task. Can someone please help me out on this.
Thanks !!
Regards,
Rama (2 Replies)
Discussion started by: ramagore85
2 Replies
LEARN ABOUT DEBIAN
scrounge-ntfs
scrounge-ntfs(8) BSD System Manager's Manual scrounge-ntfs(8)
NAME
scrounge-ntfs -- helps retrieve data from corrupted NTFS partitions
SYNOPSIS
scrounge-ntfs -l disk
scrounge-ntfs -s disk
scrounge-ntfs [-m mftoffset] [-c clustersize] [-o outdir] disk start end
DESCRIPTION
scrounge-ntfs is a utility that can rescue data from corrupted NTFS partitions. It writes the files retrieved to another working file system.
Certain information about the partition needs to be known in advance.
The -l mode is meant to be run in advance of the data corruption, with the output stored away in a file. This allows scrounge-ntfs to recover
data reliably. See the 'NOTES' section below for recover info when this isn't the case.
OPTIONS
The options are as follows:
-c The cluster size (in sectors). When not specified a default of 8 is used.
-l List partition information for a drive. This will only work when the partition table for the given drive is intact.
-m When recovering data this specifies the location of the MFT from the beginning of the partition (in sectors). If not specified
then no directory information can be used, that is, all rescued files will be written to the same directory.
-o Directory to put rescued files in. If not specified then files will be placed in the current directory.
-s Search disk for partition information. (Not implemented yet).
disk The raw device used to access the disk which contains the NTFS partition to rescue files from. eg: '/dev/hdc'
start The beginning of the NTFS partition (in sectors).
end The end of the NTFS partition (in sectors)
NOTES
If you plan on using this program sucessfully you should prepare in advance by storing a copy of the partition information. Use the -l option
to do this. Eventually searching for disk partition information will be implemented, which will solve this problem.
When only one partition exists on a disk or you want to rescue the first partition there are ways to guess at the sector sizes and MFT loca-
tion. See the scrounge-ntfs web page for more info:
http://memberwebs.com/swalter/software/scrounge/
AUTHOR
Stef Walter <stef@memberwebs.com>
scrounge-ntfs June 1, 2019 scrounge-ntfs