Sponsored Content
Operating Systems Solaris CMOS settings on SUN V20Z from Solaris10 Post 302090780 by mponjevic on Wednesday 27th of September 2006 12:01:48 PM
Old 09-27-2006
CMOS settings

Quote:
Originally Posted by BOFH
I think you're looking for the eeprom command. You can view and change the Open Boot Prom settings, the SunFire server equivalent of a PC CMOS.

Carl
Carl,

thanks for your reply. It's not eeprom command. This machine is like a PC, it's' x86 architecture. And Solaris is also x86, of course. When it boots , it boots Phenix BIOS first, then Solaris kicks in.

What I am after is this PC like CMOS settings, but if possible from Solaris prompt.

Anyway, thanks again
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

cmos check sums

not entirely unix orientated but.... anyway i've got an old 486dx? 100 that i'll looking to turn into a unix running machine. But everytime i turn it on it comes up with and invalid CMOS checksum, after i've been into the set up and reset that it works fine, tried a new batter and that didn't sort... (1 Reply)
Discussion started by: stevox
1 Replies

2. Windows & DOS: Issues & Discussions

EISA CMOS checksum error

I have a UNIX server w/an Adaptec aha-2740 card and i keep getting this error during post: EISA CMOS checksum error. It then tries to boot from the floppy. Upon researching this problem i found that it could be one of two things. Either it is the battery on the m/b (which i have all but ruled out),... (3 Replies)
Discussion started by: dlee35
3 Replies

3. Solaris

SUN Solaris10 DVD

Hello All, Please let me know how to order free sun sloaris10 dvd from sun microsystem? Prashant (1 Reply)
Discussion started by: prashant_ohol
1 Replies

4. Solaris

Sun Solaris10

hi to all, I am newuser can anyone tell me from where i get the sun solaris 10 dumps. plz mail me at (no email addresses - read the RULES of these forums) (2 Replies)
Discussion started by: quickgun
2 Replies

5. Solaris

Solaris10

Hi All How can we verify if any of the parameters we have change in Solaris10 after reboot. Like is there any command? Please advice Thanks (3 Replies)
Discussion started by: imran721
3 Replies

6. Solaris

Sun Solaris 10 FTP settings

Hi, I have a question, I have a legacy windows application that download files using FTP..The server previously was a Windows based server but it was upgraded to Sun Solaris 10. And that was when the application stopped working. After a long time of troubleshooting, I might have found that the... (4 Replies)
Discussion started by: brian12988
4 Replies

7. Solaris

How to obtain DNS Zone transfer settings on Sun OS 5.7

I have an old Sun SparcStation 5 that is running Sun OS 5.7, I'm not sure which commands would allow me to obtain the DNS zone transfer settings? 1.) I'm needing to know if the zone transfers are enabled. 2.) If it is enabled, does it transfer to specific servers 3.) If so, how do I go about... (1 Reply)
Discussion started by: Fhistleb
1 Replies

8. Hardware

Sun fire 4270 reset BIOS settings after reboot

Hello, I am trying to perform Suse 10 SP3 installation via network in 6 Sun Fire 4270 M2 servers. The problem is that even if i set first prio boot device the hard disk the system always try to boot from network.And after the first restart the BIOS setting has been lost(and PXE come first... (2 Replies)
Discussion started by: @dagio
2 Replies

9. Solaris

V20z terribly loud - firmware update?

Hello there! I am familiar with Linux, FreeBSD, but relatively new to Solaris. Because I wanted to play a little with servers and networks, I got a used SunFire v20z with AMD Opteron processors and installed OpenIndiana 151a8 on top of that. This is the first machine of this kind I have ever... (1 Reply)
Discussion started by: guru987
1 Replies
ibtl(7D)							      Devices								  ibtl(7D)

NAME
ibtl - Solaris InfiniBand Transport Layer DESCRIPTION
InfiniBand (IB) is an I/O technology based on switched fabrics. The Solaris InfiniBand Transport Layer (IBTL) is a Solaris kernel misc mod- ule and adheres to the IB Architecture Version 1.1 specification and provides a transport layer abstraction to IB client drivers. IBTL implements the programming interfaces for the Solaris InfiniBand Transport Framework (IBTF), consisting of the IB Channel Interface (CI) and the IB Transport Interface (TI). The CI consists of Host Channel Adapters (HCAs) and HCA drivers. A host is attached to the IB fabric through the CI layer. The Solaris InfiniBand CI is Sun's API rendering of the InfiniBand Architecture (IBTA) "verbs" specification. The Solaris InfiniBand TI is the kernel service driver interface into the Solaris InfiniBand Transport Framework. It provides transport and communications setup programming interfaces for Unreliable Datagram (UD) and Reliable Connected (RC) transport types only. FILES
/kernel/misc/ibtl 32-bit x86 ELF kernel misc module /kernel/misc/amd64/ibtl 64-bit x86 ELF kernel misc module /kernel/misc/sparcv9/ibtl 64-bit SPARC ELF kernel module ATTRIBUTES
See attributes(5) for a description of the following attribute: +-----------------------------+-----------------------------+ |ATTRIBUTE TYPE |ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Interface Stability |Consolidation Private | +-----------------------------+-----------------------------+ |Availability |SUNWhea, SUNWib | +-----------------------------+-----------------------------+ SEE ALSO
attributes(5), ib(7D), ibcm(7D), ibdm(7D) InfiniBand Architecture Specification, Volume 1: Release 1.1 SunOS 5.11 9 Oct 2004 ibtl(7D)
All times are GMT -4. The time now is 09:22 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy