Sponsored Content
Full Discussion: Tunable kernel parameters
Top Forums UNIX for Advanced & Expert Users Tunable kernel parameters Post 302090081 by RTM on Friday 22nd of September 2006 10:18:51 AM
Old 09-22-2006
Take a look at Forcing a dump on UnixWare 7 - it should help.
 

10 More Discussions You Might Find Interesting

1. HP-UX

kernel parameters

I want to change some kernel parameters in HP-UX11, to do with Oracle upgrade/install. I know this is done using SAM. I am told SAM will not let you enter values outside the allowable range. Could anyone tell me if they have experienced anything different? In Solaris, I would copy the... (2 Replies)
Discussion started by: malcqv
2 Replies

2. HP-UX

Need to look at Kernel parameters

Hello all, Can anyone tell me the command line I can use to look at the following Kernel parameters: nfile maxfile maxfile_lim I'm using the Reflection manager connection to my Unix box so I can't use SAM. (3 Replies)
Discussion started by: impunchdrunk
3 Replies

3. HP-UX

Kernel parameters.

I've been trying to find out the following parameters of our Unix box: ==>OS version ==> patch level and the following kernel parameters =>maxfiles_lim =>maxvgs =>nproc =>msgmni =>ncsize =>nfile Could someone help me how would I find the above(commands)? Thanks, Bhagat (1 Reply)
Discussion started by: bhagat.singh-j
1 Replies

4. Solaris

list tunable parameters and its values (Solaris 8)

Does anyone knows how to list tunable kernel parameters on a Solaris 8 system? A linux sysctl -a equivalent will do the job ... (2 Replies)
Discussion started by: danielsf
2 Replies

5. Solaris

Which file is read by kernel to set its default system kernel parameters values?

Hi gurus Could anybody tell me which file is read by kernel to set its default system kernal parameters values in solaris. Here I am not taking about /etc/system file which is used to load kernal modules or to change any default system kernal parameter value Is it /dev/kmem file or something... (1 Reply)
Discussion started by: girish.batra
1 Replies

6. Solaris

Kernel Parameters

Dear All, I want to check whether all essential kernel parameters are installed in my Solaris 10 System. Is there any way to find it. And also how to tune it. Kindly help. Thanks and Regards Rj (8 Replies)
Discussion started by: jegaraman
8 Replies

7. Solaris

Kernel Parameters

Dear All, I have weblogic Portal Installed in the Server solaris 10. How can i verify whether all the kernel parameters are available for this Software and also another question is How to crosscheck a server ( Solaris 10 Sparc ) whether it has all the required kernel parameters. ... (2 Replies)
Discussion started by: jegaraman
2 Replies

8. HP-UX

Changing Dynamic Tunable parameters in the kernel

To fix an "issue" we're having I need to update SHMMAX from 1GB to 2Gb, it's a dynamic parameter so am just wondering how flexible it really is. As Oracle is running on the server do I need to shut that down to change the parameter or will it just take the change on the fly? Also how would I... (6 Replies)
Discussion started by: Turlock
6 Replies

9. AIX

5. what is tunable parameters?can i altered it ?

what is tunable parameters?can i altered it ? (2 Replies)
Discussion started by: ramraj731
2 Replies

10. UNIX for Dummies Questions & Answers

What exactly does Kernel parameters do ?

Virtual Machine running on VMWare workstation 9.2 os : RHEL 5.8 RAM : 2.5GB Swap : 2.6gb CPU : 1 virtual CPU Surprizingly I couldn't find much from googling on What exactly does Kernel parameters do ? I was under the impression that kernel parameters just set the limits/maximum for a... (2 Replies)
Discussion started by: John K
2 Replies
dump_compress_on(5)						File Formats Manual					       dump_compress_on(5)

NAME
dump_compress_on - selects whether the system dumps memory pages compressed or uncompressed when a kernel panic occurs VALUES
Failsafe Default (Allow the kernel to decide whether to dump compressed or not based on the system state at the time of the crash.) Allowed value Integer values and The setting for is used as follows: Dump uncompressed. Dump with compression for speed if possible. Recommended values (Allow the kernel to choose dump mode.) The value the kernel usually chooses is 1. DESCRIPTION
On large systems, the time required to dump system memory when a kernel panic occurs can be excessive or even prohibitive, depending on how much physical memory is installed in the system. Compressed dump capability results in smaller and faster dumps that will also take lesser time to save over into the filesystem. The (see crashconf(1M)) command and its associated configuration file control the dump compression mode in the memory dumps associated with a system crash. On rare occasions, the system may crash before is run during the boot process. On those occasions, the configuration set using the tunable will be used. The default value for this parameter is The system determines whether or not to dump compressed based on the type of crash that occurs, in this case. Note that certain types of system crash require an uncompressed crash dump. Also, the system operator may request an uncompressed crash dump at the time the dump is taken. In either of these cases, an uncompressed dump will be performed regardless of the mode selected in Who Is Expected to Change This Tunable? Only HP Field engineers should change the value of this tunable. Restrictions on Changing Changes to this tunable take effect immediately. When Should the Tunable Be Turned On? This tunable should be turned on to dump compressed when there is a system crash. What Are the Side Effects of Turning the Tunable Off? In this case, an uncompressed dump is taken always. On large memory machines, an uncompressed dump take typically three times longer than a compressed dump. When Should the Tunable Be Turned Off? The tunable should be turned off if there is a problem with compressed dumps. What Are the Side Effects of Turning the Tunable On? The system decides the dump mode based on the type of crash. What Other Tunables Should Be Changed at the Same Time? None. WARNINGS
All HP-UX kernel tunable parameters are release specific. This parameter may be removed or have its meaning changed in future releases of HP-UX. Installation of optional kernel software, from HP or other vendors, may cause changes to tunable parameter values. After installation, some tunable parameters may no longer be at the default or recommended values. For information about the effects of installation on tun- able values, consult the documentation for the kernel software being installed. For information about optional kernel software that was factory installed on your system, see at AUTHOR
was developed by Hewlett-Packard Company. SEE ALSO
crashconf(1M), alwaysdump(5), dontdump(5). Tunable Kernel Parameters dump_compress_on(5)
All times are GMT -4. The time now is 11:05 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy