Sponsored Content
Full Discussion: RedHat 9 Force full duplex
Operating Systems Linux Red Hat RedHat 9 Force full duplex Post 302089972 by bubba112557 on Thursday 21st of September 2006 06:04:03 PM
Old 09-21-2006
RedHat 9 Force full duplex

All,

I have a RedHat 9 box which I need to figure out how to get it to stay in full duplex mode after a reboot.

I have tried

ethtool -s eth0 speed 100 duplex full autoneg off

I have tried to add a line to the /etc/sysconfig/network-scripts/ifcfg-eth0 like this:

ETHTOOL_OPTS="speed 100 duplex full autoneg off"

It does not work.

Anybody have any ideas?

Thanks,

Mike
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to configure Full Duplex and TCP/IP

We are using ZIX 4.3.3 and we need to configure the NIC for ful duplexing and we also need to configure it for a TCP/IP default gateway and DNS server to acccess the Interent. Can you please tell me the commands and procedures for configuring this? Thanks Marc (2 Replies)
Discussion started by: marc3483
2 Replies

2. UNIX for Dummies Questions & Answers

Full duplex at HUB?

Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub. Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to. ... (4 Replies)
Discussion started by: merlin
4 Replies

3. UNIX for Dummies Questions & Answers

Full Duplex Howto

Dear Members, I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
Discussion started by: Phobos
4 Replies

4. Programming

full -duplex ?

what is meant by full duplex and half duplex? b'coz in differences b\w hub and switch ,i heard lot this duplex word so please help me (1 Reply)
Discussion started by: parvathy
1 Replies

5. Solaris

100 gigabit full duplex

How can I tell on Solaris 9 sparc if my nics are running 100 gigabit full duplex... (4 Replies)
Discussion started by: csaunders
4 Replies

6. Solaris

How to force a full duplex

I need to change some Ip addresses for my servers to reflect in the NIS map. I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards. I can change the IP by doing ifconfig <NIC card > plumb up <newip>. Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies

7. SuSE

configure full duplex

How do I configure full duplex on suse 8.2 I tried ethtool -s eth0 speed 100 duplex full autoneg off the above works but when I reboot the machine the configure was lost. How do I configure full duplex so that when the machine get rebooted the configuration will stay. My interface... (4 Replies)
Discussion started by: hassan2
4 Replies

8. UNIX for Advanced & Expert Users

How to set full duplex for solaris 5.5

I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5. #ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Discussion started by: csreenivas
6 Replies

9. Solaris

How to find half duplex or full duplex

Hi, How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct? Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies

10. UNIX for Advanced & Expert Users

100Mb/s full duplex link

Hi, I have been trying to connect two computers directly through their LAN cards. One is a 3com 3c905c 10/100 Mbit/s card and the other is an Intel i217-lm 10/100/1000Mbit/s card. I have connected them through a CAT 6 cable. Whenever autoneg is turned on, the PCs connect in the 10Mb/s mode, and... (7 Replies)
Discussion started by: jamie_123
7 Replies
sg_get_network_iface_stats(3)				     Library Functions Manual				     sg_get_network_iface_stats(3)

NAME
sg_get_network_iface_stats - get network interface statistics SYNOPSIS
#include <statgrab.h> sg_network_iface_stats *sg_get_network_iface_stats(int *entries); DESCRIPTION
The sg_get_network_iface_stats function takes a pointer to an int, entries, which is filled with the number of network interfaces the machine has. This is needed to know how many sg_network_iface_stats structures have been returned. A pointer is returned to the first sg_network_iface_stats. sg_get_network_iface_stats returns statistics about the network interfaces in the machine. Specifically, it returns the speed of the inter- face, the duplex state, and whether it is currently up. RETURN VALUES
The sg_get_network_iface_stats returns a pointer to a structure of type sg_network_iface_stats. typedef enum{ SG_IFACE_DUPLEX_FULL, SG_IFACE_DUPLEX_HALF, SG_IFACE_DUPLEX_UNKNOWN }sg_iface_duplex; Note: The SG_IFACE_DUPLEX_UNKNOWN value could mean that duplex hasn't been negotiated yet. typedef struct{ char *interface_name; int speed; sg_iface_duplex duplex; int up; }sg_network_iface_stats; interface_name The name known to the operating system. (eg. on linux it might be eth0) speed The speed of the interface, in megabits/sec. duplex The duplex state the interface is in. See sg_iface_duplex for permitted values. up Whether the interface is up. SEE ALSO
statgrab(3) WEBSITE
http://www.i-scream.org/libstatgrab/ i-scream $Date: 2005/07/13 09:31:53 $ sg_get_network_iface_stats(3)
All times are GMT -4. The time now is 08:43 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy