09-18-2006
Helo. It's been a long time since I last used parted, but the steps should be:
- Create a partition.
- Create a file system.
- Create a mount point, if it does not already exist, and
- mount it: mount /dev/<partitionname> /mount/point
Regards.
10 More Discussions You Might Find Interesting
1. Solaris
Hello,
I have a problem on my sun station, that run solaris7.
To free temporarly a little space on /, I moved a few empty folders (mnt, net, awk, tftpboot) to the /home partition.
Unfortunately the system froze just after this...maybe I should not have move this files, I don't know, I am a... (3 Replies)
Discussion started by: nabulus
3 Replies
2. Solaris
dear all,
that is my problem :
c0d0p1 is nt,
c0d0p2 is solaris
and other on extended partition is pcfs,
so how can i mount it somewhere?
because i dont know which one connect from raw to block dev.
/dev/rdsk/c0d0p?
any help would be great... :) (6 Replies)
Discussion started by: stdout
6 Replies
3. Solaris
Hi there
Should mention, I am Oracle DBA. Installed Solaris 10 on VM Ware.
Created a partition, no hassle there. Modified vfstab, but made a typo, after reboot, received error message.
See attached...
Any ideas, be greatly appreciated. (2 Replies)
Discussion started by: Ackers
2 Replies
4. Filesystems, Disks and Memory
Hello,
I have a RHEL system with two 500GB hard drives in RAID 1 (I think hardware, but not 100% certain - any way to tell?).
It looks like it was just set up in default configuration with a small boot partition and one huge partition for the rest, which composes a LVM volume.
I want... (1 Reply)
Discussion started by: builder88
1 Replies
5. UNIX for Dummies Questions & Answers
Hello,
Im new here, and may be my question is stupid, but...
Today I run PGP Desktop decript on my 2nd partition ( D:\ ) and when decript finish, I restart my PC.Now when I try to open D:\ its give me: D:\ is not accessable and I lose my files :(
So I load Linux live CD ( knoppix ) and try to... (1 Reply)
Discussion started by: mrowcp
1 Replies
6. Solaris
This was my intial setup of the partition table.
Part Tag Flag Cylinders Size Blocks
0 root wm 259 - 2666 4.70GB (2408/0/0) 9863168
1 swap wu 3 - 258 512.00MB (256/0/0) 1048576
2 backup wm 0 -... (8 Replies)
Discussion started by: chidori
8 Replies
7. Shell Programming and Scripting
Hello folks,
I have 2.4TB san storage i want to make 4 partition each having 600GB. I use fdisk but not possible to do this because of fdisk limitation. So i tried parted but it make 2.4TB one partition but with parted not possible to make 4 partition having 600GB, may be i m doing wrong, can... (6 Replies)
Discussion started by: learnbash
6 Replies
8. Solaris
hi all
while formatting hard disk i am getting following error.
Partition 1 ends at 266338338
It must be between 34 and 143374704.
label error: EFI Labels do not support overlapping partitions
Partition 8 overlaps partition 1.
Warning: error writing EFI.
Label failed.
I have formatted the... (2 Replies)
Discussion started by: nikhil kasar
2 Replies
9. Red Hat
Hello All,
I have a Red Hat Linux 5.9 Server installed with one hard disk & 2 Partitions created on it as follows,
/boot - Linux Partition & another is
LVM - One VG & under that 5-6 Logical volumes(var,opt,home etc).
Here my requirement is to take out 1GB of space from LVM ( Any logical... (5 Replies)
Discussion started by: gr8_usk
5 Replies
10. AIX
Hello, today i get some aix errors (can't lock files and strange things) then i umount FS to do a fsck but i get these errors
root@omega / > fsck -p /dev/fslv06
The current volume is: /dev/fslv06
Unable to read primary superblock.
Unable to read either superblock.
I readed on this page... (9 Replies)
Discussion started by: thorin666
9 Replies
LEARN ABOUT CENTOS
mount.nfs
MOUNT.NFS(8) System Manager's Manual MOUNT.NFS(8)
NAME
mount.nfs, mount.nfs4 - mount a Network File System
SYNOPSIS
mount.nfs remotetarget dir [-rvVwfnsh ] [-o options]
DESCRIPTION
mount.nfs is a part of nfs(5) utilities package, which provides NFS client functionality.
mount.nfs is meant to be used by the mount(8) command for mounting NFS shares. This subcommand, however, can also be used as a standalone
command with limited functionality.
mount.nfs4 is used for mounting NFSv4 file system, while mount.nfs is used to mount NFS file systems versions 3 or 2. remotetarget is a
server share usually in the form of servername:/path/to/share. dir is the directory on which the file system is to be mounted.
OPTIONS
-r Mount file system readonly.
-v Be verbose.
-V Print version.
-w Mount file system read-write.
-f Fake mount. Don't actually call the mount system call.
-n Do not update /etc/mtab. By default, an entry is created in /etc/mtab for every mounted file system. Use this option to skip making
an entry.
-s Tolerate sloppy mount options rather than fail.
-h Print help message.
nfsoptions
Refer to nfs(5) or mount(8) manual pages.
NOTE
For further information please refer nfs(5) and mount(8) manual pages.
FILES
/etc/fstab file system table
/etc/mtab table of mounted file systems
SEE ALSO
nfs(5), mount(8),
AUTHOR
Amit Gud <agud@redhat.com>
5 Jun 2006 MOUNT.NFS(8)