08-29-2006
The gateways get "stuck" sometimes in AIX. Makes no sense. I just delete the network interface completely, and reconfigure it from scratch.
rmdev -dl en0
chfmgr
smitty tcpip
9 More Discussions You Might Find Interesting
1. SCO
Dear sir,
I am using sco open server 5.06.How we can reboot the system without using root password? Whar are the permision need to change to do this.
Thanks,
Mostafizur Rahman (3 Replies)
Discussion started by: rahmanm
3 Replies
2. Shell Programming and Scripting
I want to get an email alert from a cronjob when a server got rebooted unexpectedly. Please help. Thanks! :confused: (2 Replies)
Discussion started by: angloi
2 Replies
3. UNIX for Advanced & Expert Users
hi all, :)
for a reboot of sun box for patch installation i would like to know where do the reboot logs apart from /var/adm/messages and patch run messages would be available,
i would like to know the sequence of messages logged in the file like
requesting the users to log out
sending a... (1 Reply)
Discussion started by: matrixmadhan
1 Replies
4. Solaris
I'm not an advanced user by any strech, that being said here is my problem:
I ran "reboot" on a sun blade 2500
When loading up it runs through the usual routine, checking disks, filesystems and then it locks up
after the following message:
*****
starting rpc services: rpcbind... (6 Replies)
Discussion started by: eyukins
6 Replies
5. Solaris
Hi All,
I want to know the procedure like if server is down, i want to reboot the server through console ($rsc or $sc prompt).Could you please help me out.
I would really appreciate your cooperation.
thanks for understanding
regards
krishna (5 Replies)
Discussion started by: murthy76
5 Replies
6. Solaris
Hi Gurus
Recently i had change the gateway for a server
i had change the IP in the /etc/defaultrouter
and run the below command
# route add default 10.86.33.222
# route delete default 10.86.33.1
# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref ... (2 Replies)
Discussion started by: SmartAntz
2 Replies
7. Linux
We reboot our linux servers daily. Is it needed ? (10 Replies)
Discussion started by: linuxadmin
10 Replies
8. Solaris
Hi,
anyone please let us know how to write shell script to find the missing mountpoints after server reboot.
i want to take the mountpount information before server reboot, and validate the mountpoints after server reboot if any missing.please let us know the shell script from begining to end as... (24 Replies)
Discussion started by: VenkatReddy786
24 Replies
9. Red Hat
Hi,
The server got rebooted and below messages can be seen in /var/log/messages
Sep 7 10:49:12 minersville kernel: Call Trace: <IRQ> <ffffffff80167420>{__alloc_pages+796}
Sep 7 10:49:12 minersville kernel: <ffffffff80182814>{kmem_getpages+106} <ffffffff80183c16>{fallback_alloc+304}... (3 Replies)
Discussion started by: admin_db
3 Replies
LEARN ABOUT OPENDARWIN
dpkg-reconfigure
DPKG-RECONFIGURE(8) Debconf DPKG-RECONFIGURE(8)
NAME
dpkg-reconfigure - reconfigure an already installed package
SYNOPSIS
dpkg-reconfigure [options] packages
DESCRIPTION
dpkg-reconfigure reconfigures packages after they have already been installed. Pass it the names of a package or packages to reconfigure.
It will ask configuration questions, much like when the package was first installed.
If you just want to see the current configuration of a package, see debconf-show(1) instead.
OPTIONS
-ftype, --frontend=type
Select the frontend to use. The default frontend can be permanently changed by:
dpkg-reconfigure debconf
Note that if you normally have debconf set to use the noninteractive frontend, dpkg-reconfigure will use the dialog frontend instead,
so you actually get to reconfigure the package.
-pvalue, --priority=value
Specify the minimum priority of question that will be displayed. dpkg-reconfigure normally shows low priority questions no matter what
your default priority is. See debconf(7) for a list.
--default-priority
Use whatever the default priority of question is, instead of forcing the priority to low.
-u, --unseen-only
By default, all questions are shown, even if they have already been answered. If this parameter is set though, only questions that have
not yet been seen will be asked.
--force
Force dpkg-reconfigure to reconfigure a package even if the package is in an inconsistent or broken state. Use with caution.
--no-reload
Prevent dpkg-reconfigure from reloading templates. Use with caution; this will prevent dpkg-reconfigure from repairing broken templates
databases. However, it may be useful in constrained environments where rewriting the templates database is expensive.
-h, --help
Display usage help.
SEE ALSO
debconf(7)
AUTHOR
Joey Hess <joeyh@debian.org>
2018-02-28 DPKG-RECONFIGURE(8)